Re: [CAD_CAM_EDM_DRO] Re: SLA7062 technical stuff

This is direct from HobbyCNC's website:

Recommended Transformer link:
24VAC 10A Triad (Magnetek) Allied Electronics part #9678482 (115VAC Only).

I have one of HobbyCNC's board and nowhere in the documentation does it say run it at 42 VDC. The above transformer will output 34 VDC once rectified. Thats what they recommend.

I've dealt with HobbyCNC and was quite satisfied with the product and service. In the future, when I need more of these cards, I will definitely be buying from him. And I may need alot of them <G>

Ron

turyga1963 <TIntruder@...> wrote:
Dave,

Good to know. Problem in my case and I suspect that of many others
who have had similar problems is that we were expressly told by HCNC
that we could use up to 42vdc and the circuit board is even
silkscreened to show that voltage. Further we were told the closer
to 42vdc we got, the better as that would insure maximum power/speed
from the steppers.

Oh well, live and learn...

Tom

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
wrote:

>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "jeffalanp"

wrote:

> >
> >
> > Hi,
> >
> > >--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turyga1963"

> > >wrote:
> > > Being that a great number of postings on the HobbyCNC group

are by

> > > customers who need replacement 7062s, perhaps Dave kicked me

out

> > > because I disrupted a major source of income for him??? I'm
> > > guessing the $3 reduction is costing him a couple hundred a

month.

> > > At least.
> >
> > So it would appear that the SLA7062 is perhaps not as robust

as has

> > been previously suggested. I guess they do go 'pop' as well, if

they

> > are abused, similar to an abused A3977SED.
> >
> > This would most likely be to shorting of phases to one another

or

> > ground, as the disconnect is generally covered by the internal

diodes

> > I mentioned before.
> >
> > Jeff
> >
>
> Mariss has done some of the research. it's been awhile, but IIRC,
> spinning a stepper near max and then decelrating it relativly

quickly

> will/can result in about a 20% over voltage.
>
> That would mean the A3977 with it's 35 volts max would mean 28

volts

> is the best power supply voltage. and the 7062 with it's 44 volts
> would best be powered by a 36 volt supply.
>
> Since Mariss uses a 20% safety factor on his drives, I think it

would

> be a safe bet to use the same rating.
>
> Dave
>
>
>
> Dave
>

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links










[Non-text portions of this message have been removed]