CAD CAM EDM DRO - Yahoo Group Archive

SLA7062 and Re: New Article Posted

Posted by ballendo
on 2006-05-08 19:48:42 UTC
>In CCED, "jeffalanp" <xylotex@...> wrote:
>So it would appear that the SLA7062 is perhaps not as robust as has
>been previously suggested. I guess they do go 'pop' as well, if
>they are abused, similar to an abused A3977SED.

Sure. I'd guess anything abused will "pop" at some point.

The issue IMO is what constitutes "abuse", and more importantly
where that level which constitutes abuse falls within
what's "typical" for the user to do, and have.

As I mentioned, I didn't know that HCNC boards were frying chips and
traces until yesterday. (AND I understand that HCNC is dealing with
the issues of a user-built product; so I'll cut GENEROUS slack for
that!)

We haven't had any pops except those which we purposely tested to
destruction during product development and evaluation.

When you sell to users who are not electronics savvy, you have to
factor in for the inevitable errors in construction and application.
Unless you take that out of the equation by not selling user-built
electronics. That's why we don't offer electronic "kits". Or bare
boards.

As long as you don't unplug the supplied or approved motors while
under power, and use a proper A/C line supply; if ours pop, it's our
fault. We'll fix them.

Probably by just sending out a new box; so you're up and running
again as quickly as possible. We DEFINITELY will want that old box
back to see if we can determine what happened... To improve the
product and increase satisfaction for subsequent customers.

So far, no pops. Just plug and use.

Ballendo
CNCresource support

Discussion Thread

Phil Mattison 2006-05-06 10:54:19 UTC New Article Posted lcdpublishing 2006-05-06 14:04:40 UTC Re: New Article Posted Dave Rigotti 2006-05-06 15:12:13 UTC Re: New Article Posted Phil Mattison 2006-05-06 15:16:53 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted turbulatordude 2006-05-06 15:55:53 UTC Re: New Article Posted Dave Rigotti 2006-05-06 17:29:17 UTC Re: New Article Posted wanliker@a... 2006-05-06 18:50:57 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted ballendo 2006-05-06 20:08:11 UTC Re: New Article Posted ballendo 2006-05-06 20:33:19 UTC missed steps going into sync mode? Re: New Article Posted ballendo 2006-05-07 01:04:56 UTC Re: New Article Posted Dave Rigotti 2006-05-07 04:42:40 UTC Re: New Article Posted Phil Mattison 2006-05-07 10:01:43 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted Phil Mattison 2006-05-07 10:28:55 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted Phil Mattison 2006-05-07 10:34:48 UTC Re: [CAD_CAM_EDM_DRO] missed steps going into sync mode? Re: New Article Posted ballendo 2006-05-07 18:03:59 UTC Re: New Article Posted ballendo 2006-05-07 18:15:42 UTC Re: New Article Posted Phil Mattison 2006-05-07 18:41:02 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted turyga1963 2006-05-07 21:55:42 UTC Re: New Article Posted turbulatordude 2006-05-07 21:57:23 UTC Re: New Article Posted wanliker@a... 2006-05-07 22:07:37 UTC New Article Posted turyga1963 2006-05-08 00:25:30 UTC Re: New Article Posted ballendo 2006-05-08 03:25:17 UTC Re: New Article Posted Alan Marconett 2006-05-08 08:31:35 UTC RE: [CAD_CAM_EDM_DRO] Re: New Article Posted jeffalanp 2006-05-08 08:34:47 UTC SLA7062 and Re: New Article Posted turbulatordude 2006-05-08 08:40:12 UTC Re: New Article Posted Codesuidae 2006-05-08 08:50:26 UTC Re: [CAD_CAM_EDM_DRO] SLA7062 and Re: New Article Posted Codesuidae 2006-05-08 09:08:39 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted turbulatordude 2006-05-08 09:15:26 UTC SLA7062 technical stuff wanliker@a... 2006-05-08 10:04:12 UTC New Article Posted cncnovice 2006-05-08 11:04:30 UTC Re: New Article Posted wanliker@a... 2006-05-08 11:16:32 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted cncnovice 2006-05-08 11:37:54 UTC Re: New Article Posted Codesuidae 2006-05-08 12:57:24 UTC Re: [CAD_CAM_EDM_DRO] Re: New Article Posted turyga1963 2006-05-08 14:13:40 UTC SLA7062 and Re: New Article Posted turyga1963 2006-05-08 14:22:17 UTC Re: SLA7062 technical stuff turyga1963 2006-05-08 14:23:54 UTC SLA7062 and Re: New Article Posted turbulatordude 2006-05-08 14:43:26 UTC Re: New Article Posted - Moderators warning turbulatordude 2006-05-08 14:51:32 UTC Re: SLA7062 technical stuff - supply voltages turyga1963 2006-05-08 15:01:10 UTC Re: New Article Posted turyga1963 2006-05-08 15:16:18 UTC Re: New Article Posted turyga1963 2006-05-08 15:21:01 UTC Re: SLA7062 technical stuff - supply voltages John Dammeyer 2006-05-08 15:29:03 UTC RE: [CAD_CAM_EDM_DRO] Re: SLA7062 technical stuff - supply voltages Paul Kelly 2006-05-08 15:32:39 UTC RE: [CAD_CAM_EDM_DRO] Re: SLA7062 technical stuff - supply voltages R Rogers 2006-05-08 16:07:06 UTC Re: [CAD_CAM_EDM_DRO] Re: SLA7062 technical stuff turbulatordude 2006-05-08 18:43:15 UTC Re: SLA7062 technical stuff - supply voltages ballendo 2006-05-08 19:48:42 UTC SLA7062 and Re: New Article Posted ballendo 2006-05-08 20:21:07 UTC Sync mode musings was Re: New Article Posted jeffalanp 2006-05-08 20:28:56 UTC SLA7062 and Re: New Article Posted ballendo 2006-05-08 22:38:17 UTC OT SLA7062 and Re: New Article Posted Lester Caine 2006-05-08 23:14:12 UTC Re: [CAD_CAM_EDM_DRO] SLA7062 and Re: New Article Posted wanliker@a... 2006-05-08 23:24:59 UTC Re: [CAD_CAM_EDM_DRO] SLA7062 and Re: New Article Posted Mariss Freimanis 2006-05-09 10:11:39 UTC Re: SLA7062 technical stuff - supply voltages turyga1963 2006-05-10 22:50:16 UTC Re: SLA7062 technical stuff - supply voltages Mariss Freimanis 2006-05-11 06:36:52 UTC Re: SLA7062 technical stuff - supply voltages Alan Rothenbush 2006-06-12 12:21:45 UTC Re: SLA7062 technical stuff - supply voltages