RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Posted by
Larry Olson
on 2006-06-02 12:09:16 UTC
How do you look at leakage current?
-----Original Message-----
From: wanliker@... [mailto:wanliker@...]
Sent: Friday, June 02, 2006 10:15 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
In a message dated 6/2/2006 11:08:45 A.M. Mountain Daylight Time,
n4ft@... writes:
he reforms the capacitors using a variac. He starts the voltage very
low and slowly brings it to normal over several hours.
The variac will put out a variable AC voltage, so you have to run its
output
thru a Rectifier before the voltage is applied to a capacitor.
You can start reforming it with a battery charger, observe polarity.
Then
apply power supply voltage via about a 1K resistor, for short periods.
The
lower power supply voltages would be best, main thing it to take the
voltage up
slowly over a period of hours, in as small steps as possible with the
equipment you have available. I have an old Heathkit DC HV supply, so
I just hook it
up and bring it up a few volts at a time over a day or two. In that
case,
I can also watch the leakage current. I set it below the place where
it
starts to climb rapidly
bill
[Non-text portions of this message have been removed]
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
-----Original Message-----
From: wanliker@... [mailto:wanliker@...]
Sent: Friday, June 02, 2006 10:15 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
In a message dated 6/2/2006 11:08:45 A.M. Mountain Daylight Time,
n4ft@... writes:
he reforms the capacitors using a variac. He starts the voltage very
low and slowly brings it to normal over several hours.
The variac will put out a variable AC voltage, so you have to run its
output
thru a Rectifier before the voltage is applied to a capacitor.
You can start reforming it with a battery charger, observe polarity.
Then
apply power supply voltage via about a 1K resistor, for short periods.
The
lower power supply voltages would be best, main thing it to take the
voltage up
slowly over a period of hours, in as small steps as possible with the
equipment you have available. I have an old Heathkit DC HV supply, so
I just hook it
up and bring it up a few volts at a time over a day or two. In that
case,
I can also watch the leakage current. I set it below the place where
it
starts to climb rapidly
bill
[Non-text portions of this message have been removed]
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
Discussion Thread
oldpayphones
2006-06-02 08:38:21 UTC
Charging Capacitors
rrrevels
2006-06-02 10:07:28 UTC
Re: Charging Capacitors
wanliker@a...
2006-06-02 10:24:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-02 11:29:24 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-02 12:09:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-02 12:28:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-02 12:38:00 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
rrrevels
2006-06-02 13:28:38 UTC
Re: Charging Capacitors
David Speck
2006-06-02 13:31:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-02 14:49:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
BRIAN FOLEY
2006-06-02 19:51:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
oldpayphones
2006-06-02 21:18:45 UTC
Re: Charging Capacitors
JanRwl@A...
2006-06-02 21:45:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-02 21:48:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
wanliker@a...
2006-06-02 22:43:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-03 00:23:19 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
ballendo
2006-06-03 05:22:12 UTC
Re: Charging Capacitors
ballendo
2006-06-03 05:25:49 UTC
Re: Charging Capacitors
Alan Rothenbush
2006-06-03 19:03:33 UTC
Re: [CAD_CAM_EDM_DRO] Charging Capacitors
oldpayphones
2006-06-07 10:02:04 UTC
Re: Charging Capacitors
David Speck
2006-06-07 13:31:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 13:48:57 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
David Speck
2006-06-07 14:02:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
wanliker@a...
2006-06-07 14:41:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 14:51:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 14:51:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 15:00:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
David Speck
2006-06-07 20:56:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
wanliker@a...
2006-06-07 21:19:08 UTC
Charging Capacitors
Larry Olson
2006-06-07 23:04:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Mariss Freimanis
2006-06-07 23:10:36 UTC
Re: Charging Capacitors
Larry Olson
2006-06-07 23:44:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
oldpayphones
2006-06-08 01:21:54 UTC
Re: Charging Capacitors
BRIAN FOLEY
2006-06-08 03:02:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
BRIAN FOLEY
2006-06-08 03:07:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
R Rogers
2006-06-08 06:04:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors