Re: Charging Capacitors
Posted by
ballendo
on 2006-06-03 05:25:49 UTC
Hello,
If you use the lamp or 30-50K R to limit current you can turn the
voltage up near the WVDC within a few minutes with no ill effect.
And reliably reform them in an hour or so... (at least with 47Kmfd,
40 volt mallory caps<G>)
Ballendo
If you use the lamp or 30-50K R to limit current you can turn the
voltage up near the WVDC within a few minutes with no ill effect.
And reliably reform them in an hour or so... (at least with 47Kmfd,
40 volt mallory caps<G>)
Ballendo
--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@... wrote:
>
>
> In a message dated 6/2/2006 11:08:45 A.M. Mountain Daylight Time,
> n4ft@... writes:
>
> he reforms the capacitors using a variac. He starts the voltage
very
> low and slowly brings it to normal over several hours.
>
>
>
> The variac will put out a variable AC voltage, so you have to run
its output
> thru a Rectifier before the voltage is applied to a capacitor.
>
> You can start reforming it with a battery charger, observe
polarity. Then
> apply power supply voltage via about a 1K resistor, for short
periods. The
> lower power supply voltages would be best, main thing it to take
the voltage up
> slowly over a period of hours, in as small steps as possible with
the
> equipment you have available. I have an old Heathkit DC HV
supply, so I just hook it
> up and bring it up a few volts at a time over a day or two. In
that case,
> I can also watch the leakage current. I set it below the place
where it
> starts to climb rapidly
> bill
>
>
> [Non-text portions of this message have been removed]
>
Discussion Thread
oldpayphones
2006-06-02 08:38:21 UTC
Charging Capacitors
rrrevels
2006-06-02 10:07:28 UTC
Re: Charging Capacitors
wanliker@a...
2006-06-02 10:24:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-02 11:29:24 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-02 12:09:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-02 12:28:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-02 12:38:00 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
rrrevels
2006-06-02 13:28:38 UTC
Re: Charging Capacitors
David Speck
2006-06-02 13:31:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-02 14:49:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
BRIAN FOLEY
2006-06-02 19:51:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
oldpayphones
2006-06-02 21:18:45 UTC
Re: Charging Capacitors
JanRwl@A...
2006-06-02 21:45:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-02 21:48:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
wanliker@a...
2006-06-02 22:43:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Dave Halliday
2006-06-03 00:23:19 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
ballendo
2006-06-03 05:22:12 UTC
Re: Charging Capacitors
ballendo
2006-06-03 05:25:49 UTC
Re: Charging Capacitors
Alan Rothenbush
2006-06-03 19:03:33 UTC
Re: [CAD_CAM_EDM_DRO] Charging Capacitors
oldpayphones
2006-06-07 10:02:04 UTC
Re: Charging Capacitors
David Speck
2006-06-07 13:31:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 13:48:57 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
David Speck
2006-06-07 14:02:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
wanliker@a...
2006-06-07 14:41:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 14:51:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 14:51:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Larry Olson
2006-06-07 15:00:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
David Speck
2006-06-07 20:56:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
wanliker@a...
2006-06-07 21:19:08 UTC
Charging Capacitors
Larry Olson
2006-06-07 23:04:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
Mariss Freimanis
2006-06-07 23:10:36 UTC
Re: Charging Capacitors
Larry Olson
2006-06-07 23:44:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
oldpayphones
2006-06-08 01:21:54 UTC
Re: Charging Capacitors
BRIAN FOLEY
2006-06-08 03:02:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
BRIAN FOLEY
2006-06-08 03:07:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors
R Rogers
2006-06-08 06:04:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Charging Capacitors