Stepper motor 101 was Re: Lini-stepper
Posted by
Steve Stallings
on 2006-08-10 09:17:41 UTC
Well not exactly a no brainer.... the LiniStepper
is called a "linear" driver because its output
stages operate in the linear region NOT as switches.
Changing to MOSFETs without redesigning for use
as chopping switches will not change the power
dissipation in the output stage.
Regards,
Steve Stallings
www.PMDX.com
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@...> wrote:
is called a "linear" driver because its output
stages operate in the linear region NOT as switches.
Changing to MOSFETs without redesigning for use
as chopping switches will not change the power
dissipation in the output stage.
Regards,
Steve Stallings
www.PMDX.com
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@...> wrote:
>always
> This is where the polishing of the program and circuit needs to be
> done.
>
> Switch to FET's to lower heat. a no brainer.
>
> Linear amperage does not equal linear steps, but then there has
> been the discussion of exactly where the step/armature is on awith
> microstep. is it exactly at 1/7th of a full step, or is the power
> ramping between steps smoother that offers better power delivery ?
> and it is 'somewhere' between 1/2 steps, but not exactly linear ?
>
> Also, there is that how close is good enough bit. does a screw
> 26,000 steps per inch suffer if the step if off by 1/10th of astep ?
>
> Dave
>
Discussion Thread
rllalonde2000
2006-08-08 18:59:59 UTC
Are steppers considered low frequency motors?
Steve Stallings
2006-08-08 19:18:18 UTC
Re: Are steppers considered low frequency motors?
Mariss Freimanis
2006-08-08 20:49:49 UTC
Re: Are steppers considered low frequency motors?
ballendo
2006-08-08 21:49:27 UTC
Stepper motor 101 was Re: Are steppers considered low frequency motors?
Alan Marconett
2006-08-09 08:19:17 UTC
RE: [CAD_CAM_EDM_DRO] Stepper motor 101 was Re: Are steppers considered low frequency motors?
Mariss Freimanis
2006-08-09 09:15:28 UTC
Stepper motor 101 was Re: Are steppers considered low frequency motors?
Alan Marconett
2006-08-09 10:12:25 UTC
RE: [CAD_CAM_EDM_DRO] Stepper motor 101 was Re: Are steppers considered low frequency motors?
Dennis Schmitz
2006-08-09 20:13:06 UTC
Re: Stepper motor 101 was Re: Are steppers considered low frequency motors?
turbulatordude
2006-08-09 23:29:33 UTC
Stepper motor 101 was Re: Are steppers considered low frequency motors?
ballendo
2006-08-10 03:13:33 UTC
Stepper motor 101 was Re: Are steppers considered low frequency motors?
ballendo
2006-08-10 03:17:51 UTC
Stepper motor 101 was Re: Are steppers considered low frequency motors?
Alan Marconett
2006-08-10 08:02:12 UTC
RE: [CAD_CAM_EDM_DRO] Stepper motor 101 was Re: Are steppers considered low frequency motors?
Alan Marconett
2006-08-10 08:15:19 UTC
RE: [CAD_CAM_EDM_DRO] Stepper motor 101 was Re: Are steppers considered low frequency motors?
Dennis Schmitz
2006-08-10 08:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Stepper motor 101 was Re: Are steppers considered low frequency motors?
Alan Marconett
2006-08-10 08:23:19 UTC
RE: [CAD_CAM_EDM_DRO] Stepper motor 101 was Re: Are steppers considered low frequency motors?
turbulatordude
2006-08-10 08:27:53 UTC
Stepper motor 101 was Re: Are steppers considered low frequency motors?
turbulatordude
2006-08-10 08:46:59 UTC
Stepper motor 101 was Re: Lini-stepper
Mariss Freimanis
2006-08-10 09:13:02 UTC
Stepper motor 101 was Re: Lini-stepper
Steve Stallings
2006-08-10 09:17:41 UTC
Stepper motor 101 was Re: Lini-stepper
Kory Hamzeh
2006-08-10 10:18:26 UTC
Driving the parrallel port in WindowXP
Lester Caine
2006-08-10 10:40:21 UTC
Re: [CAD_CAM_EDM_DRO] Driving the parrallel port in WindowXP
jzmuda2000
2006-08-10 12:12:37 UTC
Stepper motor 101 was Re: Lini-stepper
Alan Marconett
2006-08-10 12:15:19 UTC
RE: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
Alan Marconett
2006-08-10 12:56:43 UTC
RE: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
Mariss Freimanis
2006-08-10 13:05:39 UTC
Stepper motor 101 was Re: Lini-stepper
Sebastien Bailard - Dubsen
2006-08-10 15:53:45 UTC
Re: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
Kory Hamzeh
2006-08-10 17:15:54 UTC
RE: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
Jon Elson
2006-08-10 18:45:47 UTC
Re: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
Sebastien Bailard - Dubsen
2006-08-10 18:55:03 UTC
Re: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
caudlet
2006-08-10 20:39:33 UTC
Re: Driving the parallel port in WindowXP
turbulatordude
2006-08-10 23:35:26 UTC
Stepper motor 101 was Re: Lini-stepper
Steve Blackmore
2006-08-10 23:51:39 UTC
Re: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
turbulatordude
2006-08-11 00:23:16 UTC
Stepper motor 101 was Re: Lini-stepper
Lester Caine
2006-08-11 01:20:41 UTC
Re: [CAD_CAM_EDM_DRO] Driving the parallel port in WindowXP
Lester Caine
2006-08-11 01:21:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Driving the parallel port in WindowXP
Sebastien Bailard - Dubsen
2006-08-11 02:54:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Driving the parallel port in WindowXP
Jon Elson
2006-08-11 09:14:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Driving the parallel port in WindowXP