Re: Backlash
Posted by
Philip Burman
on 2007-03-25 04:22:31 UTC
If you do the test with the screw fully extended and fully retracted
can you not differentiate between flexing/twisting of the screw and
flexing of the yoke. Maybe even extrapilate the error back to an
effectively zero length screw to filter out ther screw error.
Regards
Phil
can you not differentiate between flexing/twisting of the screw and
flexing of the yoke. Maybe even extrapilate the error back to an
effectively zero length screw to filter out ther screw error.
Regards
Phil
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "ballendo" <ballendo@...> wrote:
>
> One more thing...
>
> It's likely so obvious it's already been handled, but...
>
> The Bnut to yoke interface/connection...
>
> Hope this helps,
>
> Ballendo
>
> In CCED, "Vince Endter" <vince@> wrote:
> >I get the same amount of backlash if I turn the pully by hand. I
get
> >the same amount of backlash if I turn <snip>
>
Discussion Thread
Blue
2005-02-09 10:10:31 UTC
Backlash
Jon Elson
2005-02-09 11:14:37 UTC
Re: [CAD_CAM_EDM_DRO] Backlash
Blue
2005-02-09 12:06:19 UTC
Re: [CAD_CAM_EDM_DRO] Backlash
Vince Endter
2007-03-24 09:47:12 UTC
Backlash
Mark Vaughan
2007-03-24 11:25:34 UTC
RE: [CAD_CAM_EDM_DRO] Backlash
R Rogers
2007-03-24 12:17:48 UTC
Re: [CAD_CAM_EDM_DRO] Backlash
Polaraligned
2007-03-24 13:05:11 UTC
Re: Backlash
Vince Endter
2007-03-24 15:04:08 UTC
Re: Backlash
Vince Endter
2007-03-24 15:08:56 UTC
Re: Backlash
Mark Vaughan
2007-03-24 15:26:28 UTC
RE: [CAD_CAM_EDM_DRO] Re: Backlash
Polaraligned
2007-03-24 17:19:09 UTC
Re: Backlash
Jon Elson
2007-03-24 21:38:16 UTC
Re: [CAD_CAM_EDM_DRO] Backlash
Vince Endter
2007-03-24 21:45:39 UTC
Re: Backlash
ballendo
2007-03-25 00:02:24 UTC
Re: Backlash
ballendo
2007-03-25 00:06:36 UTC
Re: Backlash
Philip Burman
2007-03-25 04:22:31 UTC
Re: Backlash
Vince Endter
2007-03-25 08:12:57 UTC
Re: Backlash
Graham Stabler
2007-03-25 08:24:01 UTC
Re: Backlash
Mark Vaughan
2007-03-25 09:33:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: Backlash
Vince Endter
2007-03-25 11:24:43 UTC
Re: Backlash
Jon Elson
2007-03-25 11:33:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash
R Rogers
2007-03-25 12:31:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash
David G. LeVine
2007-03-25 13:07:26 UTC
Re: [CAD_CAM_EDM_DRO] Backlash
Mark Vaughan
2007-03-25 13:46:33 UTC
RE: [CAD_CAM_EDM_DRO] Re: Backlash
Mark Vaughan
2007-03-25 14:14:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: Backlash
Vince Endter
2007-03-25 20:17:54 UTC
Re: Backlash
Vince Endter
2007-03-25 20:19:24 UTC
Re: Backlash
Vince Endter
2007-03-25 20:22:07 UTC
Re: Backlash
David G. LeVine
2007-03-25 21:24:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash
R Rogers
2007-03-25 21:37:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash
Jon Elson
2007-03-25 21:58:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash
Jon Elson
2007-03-25 22:04:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash
Vince Endter
2007-03-26 05:09:28 UTC
Re: Backlash
Jon Elson
2007-03-26 20:57:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash
Jack Mc Kie
2008-01-13 17:39:51 UTC
Backlash
figNoggle
2008-01-13 18:36:12 UTC
Re: [CAD_CAM_EDM_DRO] Backlash
Jack McKie
2008-01-16 13:10:54 UTC
Re: [CAD_CAM_EDM_DRO] Backlash