Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Posted by
Alan Marconett KM6VV
on 2000-10-08 14:55:39 UTC
Jon,
I found the one with the small disk end, I got it to run true, and then
I approach the stock, and stop when it flies out? and that's aligned?
Thanks,
Alan
Jon Anderson wrote:
I found the one with the small disk end, I got it to run true, and then
I approach the stock, and stop when it flies out? and that's aligned?
Thanks,
Alan
Jon Anderson wrote:
>
> Alan,
>
> To use a pointed wiggler, with the spindle turning, you true up the very
> point by gently bringing it to center with something like a pin or a
> lathe tool blank. Push a bit too far, it'll jump out again. You want to
> be touching right at the tip or very close to it. Using something flat,
> hold it about 45 degrees or so. Once it's running true, you can eyeball
> the spindle over a scribe line or prick punch mark pretty closesly.
> A full wiggler set has an attachment with a small disk ground at the
> end, this functions just like a regular edge finder. Never have used any
> of the other accessories in a wiggler set.
>
> Jon (the other one)
Discussion Thread
Joe Vicars
2000-10-06 07:02:29 UTC
Lighted edge finder
MRC
2000-10-06 07:54:33 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Jon Anderson
2000-10-06 07:56:40 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
wanliker@a...
2000-10-06 08:38:59 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Jon Anderson
2000-10-06 09:06:37 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Hugh Currin
2000-10-06 09:48:20 UTC
Re: Lighted edge finder
Ron Ginger
2000-10-06 10:06:08 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-06 10:43:31 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-06 12:05:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lighted edge finder
Jon Anderson
2000-10-06 12:21:10 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Ian Wright
2000-10-06 13:31:02 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
ptengin@a...
2000-10-06 14:30:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lighted edge finder
ballendo@y...
2000-10-06 14:44:39 UTC
Re: Lighted edge finder
Alan Marconett KM6VV
2000-10-06 15:20:28 UTC
Re: Lighted edge finder
Alan Marconett KM6VV
2000-10-06 15:30:08 UTC
RE: Lighted edge finder
ptengin@a...
2000-10-06 20:30:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lighted edge finder
Jon Elson
2000-10-06 22:29:41 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Anne Ogborn
2000-10-06 22:43:31 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Rick Dulas
2000-10-07 13:00:42 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Jon Elson
2000-10-07 14:12:21 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-07 23:34:25 UTC
RE: Lighted edge finder
Alvaro Fogassa
2000-10-07 23:42:12 UTC
Re: Lighted edge finder
Jon Anderson
2000-10-08 08:44:27 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Anne Ogborn
2000-10-08 12:37:54 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-08 14:55:39 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
catboat15@a...
2000-10-08 21:04:49 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Jon Elson
2000-10-08 21:48:19 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
ballendo@y...
2000-10-09 01:14:58 UTC
Re: RE: Lighted edge finder
Alan Marconett KM6VV
2000-10-09 10:20:50 UTC
RE: Lighted edge finder
Alan Marconett KM6VV
2000-10-09 10:41:00 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Darrell
2000-10-09 10:59:43 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
catboat15@a...
2000-10-09 12:12:41 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Terry Ackland
2000-10-09 15:12:16 UTC
Re: Lighted edge finder
ballendo@y...
2000-10-09 19:56:57 UTC
Re: Lighted edge finder
Ian Wright
2000-10-10 00:55:16 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Alan Marconett KM6VV
2000-10-10 11:28:33 UTC
RE: Lighted edge finder
ptengin@a...
2000-10-11 02:47:29 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Hugh Mahlendorf
2000-10-12 23:48:01 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder