Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Posted by
Jon Anderson
on 2000-10-08 08:44:27 UTC
Alan,
To use a pointed wiggler, with the spindle turning, you true up the very
point by gently bringing it to center with something like a pin or a
lathe tool blank. Push a bit too far, it'll jump out again. You want to
be touching right at the tip or very close to it. Using something flat,
hold it about 45 degrees or so. Once it's running true, you can eyeball
the spindle over a scribe line or prick punch mark pretty closesly.
A full wiggler set has an attachment with a small disk ground at the
end, this functions just like a regular edge finder. Never have used any
of the other accessories in a wiggler set.
Jon (the other one)
To use a pointed wiggler, with the spindle turning, you true up the very
point by gently bringing it to center with something like a pin or a
lathe tool blank. Push a bit too far, it'll jump out again. You want to
be touching right at the tip or very close to it. Using something flat,
hold it about 45 degrees or so. Once it's running true, you can eyeball
the spindle over a scribe line or prick punch mark pretty closesly.
A full wiggler set has an attachment with a small disk ground at the
end, this functions just like a regular edge finder. Never have used any
of the other accessories in a wiggler set.
Jon (the other one)
Discussion Thread
Joe Vicars
2000-10-06 07:02:29 UTC
Lighted edge finder
MRC
2000-10-06 07:54:33 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Jon Anderson
2000-10-06 07:56:40 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
wanliker@a...
2000-10-06 08:38:59 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Jon Anderson
2000-10-06 09:06:37 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Hugh Currin
2000-10-06 09:48:20 UTC
Re: Lighted edge finder
Ron Ginger
2000-10-06 10:06:08 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-06 10:43:31 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-06 12:05:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lighted edge finder
Jon Anderson
2000-10-06 12:21:10 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Ian Wright
2000-10-06 13:31:02 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
ptengin@a...
2000-10-06 14:30:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lighted edge finder
ballendo@y...
2000-10-06 14:44:39 UTC
Re: Lighted edge finder
Alan Marconett KM6VV
2000-10-06 15:20:28 UTC
Re: Lighted edge finder
Alan Marconett KM6VV
2000-10-06 15:30:08 UTC
RE: Lighted edge finder
ptengin@a...
2000-10-06 20:30:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lighted edge finder
Jon Elson
2000-10-06 22:29:41 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Anne Ogborn
2000-10-06 22:43:31 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Rick Dulas
2000-10-07 13:00:42 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Jon Elson
2000-10-07 14:12:21 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-07 23:34:25 UTC
RE: Lighted edge finder
Alvaro Fogassa
2000-10-07 23:42:12 UTC
Re: Lighted edge finder
Jon Anderson
2000-10-08 08:44:27 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Anne Ogborn
2000-10-08 12:37:54 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder
Alan Marconett KM6VV
2000-10-08 14:55:39 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
catboat15@a...
2000-10-08 21:04:49 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Jon Elson
2000-10-08 21:48:19 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
ballendo@y...
2000-10-09 01:14:58 UTC
Re: RE: Lighted edge finder
Alan Marconett KM6VV
2000-10-09 10:20:50 UTC
RE: Lighted edge finder
Alan Marconett KM6VV
2000-10-09 10:41:00 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Darrell
2000-10-09 10:59:43 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
catboat15@a...
2000-10-09 12:12:41 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Terry Ackland
2000-10-09 15:12:16 UTC
Re: Lighted edge finder
ballendo@y...
2000-10-09 19:56:57 UTC
Re: Lighted edge finder
Ian Wright
2000-10-10 00:55:16 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Alan Marconett KM6VV
2000-10-10 11:28:33 UTC
RE: Lighted edge finder
ptengin@a...
2000-10-11 02:47:29 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lighted edge finder
Hugh Mahlendorf
2000-10-12 23:48:01 UTC
Re: [CAD_CAM_EDM_DRO] Lighted edge finder