CAD CAM EDM DRO - Yahoo Group Archive

BDI

on 2001-07-16 18:31:14 UTC
Hi Ray, BDI fans,

Well, I finally got an AMD K6-2/400 machine up and checked out with
Windoz98 (I had sometime previously built a machine for my wife with the
6Gb drive).

The drive is partitioned as C,D,E &F, each partition is 2Gb, except the
last, which got 32MB. Seemed like a good idea at the time; I think the
other intended target machine didn't like anything bigger then 2Gb.

As Windoz98 is in the 'C' partition, I thought I'd try to bring BDI up
on the 'E' drive partition. I selected custom (?) and gave 'E' the root
'/'.

The first problem (?) I had was in the video board/monitor choices. I
had put in an old Trident 9000 512 kb controller, and a Toshiba 17"
monitor I had. Monitor not on the list, but I determined H & V sync
rates, and put in the numbers (OK?) I tried the "test", but other then
a few flashes and clicks of the monitor, I didn't see any "graphics
screen" (Am I supposed to see something?), and the 512K selection was
deleted upon the return to the text setup screens. I continued.

The setups suggests about 15-20 min of time to copy all the "packages",
that starts but never finishes (I tried different builds, I think the
developer finished, but hung on the post stuff).

After waiting a good while, I rebooted, and with Windoz, I saw (from the
developer load try) a 1Gb or so image file, and a 32K file.

Some questions:

1) Did BDI (RedHat) not like the AMD K6?

2) Did I blow it on the 'E' partition? (it would be nice to do dual
boot), but I couldn't see a way to switch the boot to the "extended"
partition. (Something about ASKING for instructions on doing a
dual-boot in the printed note that came with the CD).

3) SHOULD I have seen something on the video test? (800x600 VGA)

4) I can and will blow away the Windoz98, if necessary (easier), but as
the drive is 6Gb, I thought I'd keep it.

5) IDE drive and CD, but couldn't boot from BDI CD (machine seems to
boot from Windoz98 2nd Ed CD). Not a problem, I made a boot floppy per
instructions on CD.

Any Ideas?

Alan KM6VV

Discussion Thread

Alan Marconett KM6VV 2001-07-16 18:31:14 UTC BDI allan_r9@h... 2001-07-16 19:28:46 UTC Re: BDI Alan Marconett KM6VV 2001-07-16 20:02:57 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Tim Goldstein 2001-07-16 20:11:40 UTC RE: [CAD_CAM_EDM_DRO] Re: BDI Jon Elson 2001-07-16 22:15:08 UTC Re: [CAD_CAM_EDM_DRO] BDI Ian Wright 2001-07-17 01:39:25 UTC Re: [CAD_CAM_EDM_DRO] BDI Ray 2001-07-17 11:54:34 UTC Re: BDI Alan Marconett KM6VV 2001-07-17 12:20:50 UTC Re: [CAD_CAM_EDM_DRO] BDI Alan Marconett KM6VV 2001-07-17 13:23:42 UTC Re: [CAD_CAM_EDM_DRO] BDI Alan Marconett KM6VV 2001-07-17 14:18:26 UTC Re: BDI Alan Marconett KM6VV 2001-07-18 15:59:03 UTC Re: BDI emserv@e... 2001-08-09 16:00:16 UTC BDI Weyland 2001-08-09 19:47:04 UTC BDI Donald Brock 2001-08-10 08:57:19 UTC Re: BDI Gene 2002-02-27 00:28:10 UTC BDI awemawson 2002-02-27 00:33:19 UTC Re: BDI Gene 2002-02-27 05:00:36 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Ed Fanta 2002-02-27 05:45:07 UTC Re: [CAD_CAM_EDM_DRO] BDI John Guenther 2002-02-27 05:45:45 UTC RE: [CAD_CAM_EDM_DRO] Re: BDI Jon Elson 2002-02-27 10:50:52 UTC Re: [CAD_CAM_EDM_DRO] BDI Gene 2002-02-27 12:44:51 UTC BDI Dave Lantz 2002-02-27 12:46:32 UTC RE: [CAD_CAM_EDM_DRO] BDI Gene 2002-02-27 14:15:59 UTC Re: [CAD_CAM_EDM_DRO] BDI Darrell Daniels 2002-02-27 22:12:52 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Dave Lantz 2002-02-28 05:05:53 UTC RE: [CAD_CAM_EDM_DRO] BDI Glen 2002-02-28 10:24:52 UTC Re: [CAD_CAM_EDM_DRO] BDI Gene 2002-04-12 11:13:50 UTC BDI Ray Henry 2002-04-12 18:58:25 UTC Re: BDI batwings@i... 2002-04-12 19:17:24 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Jon Elson 2002-04-12 22:52:24 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Ray Henry 2002-04-13 12:12:02 UTC Re: Re: Re: BDI Gene 2002-05-06 19:54:31 UTC BDI Gene 2002-05-07 09:48:40 UTC BDI Ray Henry 2002-05-07 16:32:16 UTC Re: BDI John Branlund 2002-05-07 16:44:14 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Tim Goldstein 2002-05-07 16:57:45 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Ray Henry 2002-05-07 20:11:20 UTC Re: BDI Jon Elson 2002-05-07 22:17:16 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Gene 2002-05-23 15:44:20 UTC BDI Jon Elson 2002-05-23 21:58:23 UTC Re: [CAD_CAM_EDM_DRO] BDI Ian W. Wright 2002-05-24 00:58:46 UTC Re: [CAD_CAM_EDM_DRO] BDI Ray Henry 2002-05-24 07:22:05 UTC Re: BDI Gene 2002-05-25 14:05:05 UTC BDI John Guenther 2002-05-25 17:44:11 UTC RE: [CAD_CAM_EDM_DRO] BDI William Scalione 2002-05-25 21:39:41 UTC Re: [CAD_CAM_EDM_DRO] BDI Jon Elson 2002-05-25 21:49:41 UTC Re: [CAD_CAM_EDM_DRO] BDI Ray Henry 2002-05-26 07:29:42 UTC Re: Re: BDI Gene 2002-05-27 14:04:00 UTC BDI Nic van der Walt 2002-05-27 17:46:17 UTC Servo motor controller project Jon Elson 2002-05-27 22:36:52 UTC Re: [CAD_CAM_EDM_DRO] BDI Vajk Fekete 2002-05-27 22:39:49 UTC Re: [CAD_CAM_EDM_DRO] BDI Nic van der Walt 2002-05-28 14:52:15 UTC Servo motor controller project studleylee 2002-05-28 15:27:36 UTC Re: Servo motor controller project Peter Homann 2002-05-28 16:37:46 UTC HSM Tapping Machine Article doug98105 2002-05-28 17:25:10 UTC Re: HSM Tapping Machine Article Peter Homann 2002-05-28 17:42:17 UTC RE: [CAD_CAM_EDM_DRO] Re: HSM Tapping Machine Article Keith Bowers 2002-05-28 17:52:50 UTC Re: [CAD_CAM_EDM_DRO] Servo motor controller project Marcus & Eva 2002-05-28 19:30:18 UTC Re: [CAD_CAM_EDM_DRO] Re: HSM Tapping Machine Article Peter Homann 2002-05-28 19:53:26 UTC RE: [CAD_CAM_EDM_DRO] Re: HSM Tapping Machine Article chevalier121 2002-05-29 02:18:21 UTC Re: Servo motor controller project turbulatordude 2002-05-29 04:26:15 UTC Re: HSM Tapping Machine Article doug98105 2002-05-29 06:48:53 UTC Re: HSM Tapping Machine Article steel2chips 2002-05-30 07:42:41 UTC Re: Servo motor controller project Gene 2002-07-04 14:32:50 UTC BDI dakota8833 2002-07-05 05:30:59 UTC Re: BDI Ray Henry 2002-07-05 08:03:13 UTC Re: BDI Gene 2002-07-05 10:38:18 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Jon Elson 2002-07-05 12:05:58 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI