Re: Linux/EMC

Probably 80% of the time I spent on linux/rt/emc was trying to
get the video/monitor configured in Linux to run Xwindows.
Once over that major hurdle, rt and emc were not that tough.

I did waste alot of time trying to get rt/emc to run on a 486.
Don't even try! Get an old 75mhz or 90mhz pentium. Emc will
run with only 16mb of memory. Wasted more time until I discovered
you have to have at least 600x800 svga resolution to run Tim's
script.

After all the growing pains I have installed linux/rt/emc on
subsequent machines in less than two hours.

Bob

At 06:32 PM 10/11/99 -0700, you wrote:

>From: "Steve Carlisle" <quatsein@...>
>
>Well, here's Steve's story on getting LINUX_RTLINUX_EMC
>up and running on a Pentium 100, 32 megs ram, 1 gig scsi
>hard drive, Cirrus Logic GD-5430 video, Motorola Lifestyle
>28.8 modem, cdrom and floppy.
>
>About an hour to install RH 5.2, linux for dummies
>About 15 hours to configure video for Xfree
>about 15 hours to configure to recognize modem
>About 4 hours and counting on RTlinux install, 2
>times with Tims script, 2 times with Matt's instructions,
>and I am right now on the 3rd try with Tim's script.
>
>But hey, I will not give up! And those time estimates are
>very conservative. I have used MS/Windows machines
>only before this try with Linux.
>
>Any helpful idea's I may not have tried would surely
>be welcome.
>
>Steve Carlisle
>
>----------
>From: Dan Falck <dfalck@...>
>To: CAD_CAM_EDM_DRO@onelist.com
>Subject: Re: [CAD_CAM_EDM_DRO]Linux/EMC
>Date: Monday, October 11, 1999 3:57 PM
>
>From: Dan Falck <dfalck@...>
>
>It seems like there is a lot of negative feeling going on over the
>Linux/EMC installation thing and I think that most of it is coming from
>folks who haven't tried it out. Jon Elson and Matt Shaver inspired me to
>install in my shop. They both have had great luck with it and use it every
>day- as do I now. I am not a programmer/IT specialist or computer guru in
>any way. It just happens that the instructions given by Matt, Jon, and Tim
>work! For instance, today I did a fresh install (on a Compaq 4540) of
>RedHat 5.2, Rtlinux, and EMC in 1 hour and 15 minutes. How did I do it? I
>used the install instructions that Tim gives out on his web site
>(http://www.ktmarketing.com/CNC.html).
>Why did I go with EMC? It is powerful, runs smooth, and is a lower cost
>solution than Ah-ha, Maxnc, Bestsoft, etc... There is also a lot more
>potential power with the system. The authors listen to us and implement
>new features/fix bugs. The source code is there for the programmers out
>there who want to tinker with the system.
>I use EMC in my shop to make parts and make money. I have been retrofitting
>another mill and will be installing another EMC controller within the next
>few weeks. I'm not a Linux nut, I just see a lot more potential with EMC
>than the other systems.
>
>Hoyt, I would think that you would have a great time with EMC, since you
>are a programmer already.
>
>
>
>Thanks,
>Dan
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>discussion of shop built systems in the above catagories.
>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>For the FAQ, go to http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the

discussion of shop built systems in the above catagories.

>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>For the FAQ, go to http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>