CAD CAM EDM DRO - Yahoo Group Archive

Re: Linux/EMC

on 1999-10-13 17:11:55 UTC
Jon, thanks for the SUPPORT. Over the last day I have
been looking over the boot files, and the configuration of
LILO. The boot section has extra INITRD files to configure
a ram disk, for the scsi disk I believe. The RT script of
course does not support that. I have to now figure how
to configure the extra needed files to work with Linuz-1.
Thanks for the help.

Steve

----------
From: Jon Elson <jmelson@...>
To: CAD_CAM_EDM_DRO@onelist.com
Subject: Re: [CAD_CAM_EDM_DRO]Linux/EMC
Date: Tuesday, October 12, 1999 11:02 PM

From: Jon Elson <jmelson@...>



Steve Carlisle wrote:

> From: "Steve Carlisle" <quatsein@...>
>
> Ian, As you know Linux can be configured for just
> about all hardware, and for sure that which is listed
> on the compatibility list. My machine runs well under
> Linux, with all the hardware configured. When I install
> RTLinux, the LILO configuration in the script is giving
> me problems, that I am almost posative on because
> Linux and RTLinux fail at the same point. I am sure
> I will figure it out, just like all the other hurdles. You
> learn as you go, and that is great. I can see I am
> going to enjoy Linux, as compared to Windows

The most important thing to check here is if the kernels
you are trying to load have SCSI support permanently
compiled into the kernel. If SCSI is only a loadable
option module, it won't be able to boot on a system
with a SCSI hard drive. What you can do is boot
from the floppies, and use the 'rescue' mode to gain
access to the disk, and check the options in your kernel
config file. The default kernel from the raw install should
have the SCSI support installed. Finally, if you forgot
(I've done this) you need to run lilo after any change
to the lilo config file that sets up the bootable kernels.

Jon

Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems in the above catagories.
To Unsubscribe, read archives, change to or from digest.
Go to: http://www.onelist.com/isregistered.cgi
Log on, and you will go to Member Center, and you can make changes there.
For the FAQ, go to http://www.ktmarketing.com/faq.html
bill,
List Manager

Discussion Thread

Dan Falck 1999-10-11 15:57:39 UTC Re: Linux/EMC Steve Carlisle 1999-10-11 18:32:20 UTC Re: Linux/EMC Steve Carlisle 1999-10-11 18:54:57 UTC Re: Linux/EMC Bob Bachman 1999-10-11 20:56:37 UTC Re: Linux/EMC stratton@x... 1999-10-11 18:06:57 UTC Re: Linux/EMC Steve Carlisle 1999-10-11 19:37:25 UTC Re: Linux/EMC stratton@x... 1999-10-11 18:34:35 UTC Re: Linux/EMC Steve Carlisle 1999-10-11 20:03:03 UTC Re: Linux/EMC Marshall Pharoah 1999-10-12 04:53:42 UTC Re: Linux/EMC batwings@x... 1999-10-11 10:18:33 UTC Re: Linux/EMC Darrell Gehlsen 1999-10-12 10:26:31 UTC Re: Linux/EMC Ian Wright 1999-10-12 03:43:20 UTC Re: Linux/EMC Steve Carlisle 1999-10-12 17:04:42 UTC Re: Linux/EMC Steve Carlisle 1999-10-12 17:20:32 UTC Re: Linux/EMC Jon Elson 1999-10-12 23:02:25 UTC Re: Linux/EMC Marshall Pharoah 1999-10-13 04:10:32 UTC Re: Linux/EMC Ian Wright 1999-10-13 11:21:15 UTC Re: Linux/EMC Steve Carlisle 1999-10-13 17:11:55 UTC Re: Linux/EMC Steve Carlisle 1999-10-13 17:56:39 UTC Re: Linux/EMC stratton@m... 1999-10-14 06:47:33 UTC Re: Linux/EMC Steve Carlisle 1999-10-14 08:12:44 UTC Re: Linux/EMC stratton@m... 1999-10-14 06:58:50 UTC Re: Linux/EMC Steve Carlisle 1999-10-14 08:19:50 UTC Re: Linux/EMC Ian Wright 1999-10-14 12:48:18 UTC Re: Linux/EMC Steve Carlisle 1999-10-14 17:25:18 UTC Re: Linux/EMC Steve Carlisle 1999-10-17 10:42:56 UTC Re: Linux/EMC