Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Posted by
Jon Elson
on 2002-04-04 22:43:14 UTC
jeffdavis516 wrote:
have it running one foot back and forth as fast as it can, over and over,
to see this. It is the acceleration peaks that get the current up.
Otherwise, the motors draw practically no current, therefore, no
heat. (I have LED bar graphs on my servo amps, X and Y idle
at no current, and the Z just has tiny blips as it is always playing
with the quill's weight.
Jon
> Thanks Tim,You have to have specs from the manufacturer.
>
> I kind of knew you would have the answer. Another question for you.
> How do you know where your running a motor?
> I could be running theThen, you aren't even getting close to the continuous rating point.
> servo at the continuous place, or I could be somewhere in between the
> continuous and peak? I know that when I run my jobs on the mill the
> motors remain cool to the touch.
> I have not ever felt them evenIf you run it hard enough, it WILL get warm. But, you might have to
> warm. This has always baffled me, every motor that I have used
> before (AC only) has gotten warm to the touch after use.
have it running one foot back and forth as fast as it can, over and over,
to see this. It is the acceleration peaks that get the current up.
Otherwise, the motors draw practically no current, therefore, no
heat. (I have LED bar graphs on my servo amps, X and Y idle
at no current, and the Z just has tiny blips as it is always playing
with the quill's weight.
Jon
Discussion Thread
cdoughtynz
2002-04-02 23:42:43 UTC
servo vs stepper
Steve
2002-04-03 06:27:31 UTC
Re: [CAD_CAM_EDM_DRO] servo vs stepper
jeffdavis516
2002-04-03 09:02:42 UTC
Re: servo vs stepper
Jon Elson
2002-04-03 10:33:51 UTC
Re: [CAD_CAM_EDM_DRO] servo vs stepper
Peter Seddon
2002-04-03 10:51:15 UTC
Re: [CAD_CAM_EDM_DRO] servo vs stepper
Jon Elson
2002-04-03 11:03:13 UTC
Re: [CAD_CAM_EDM_DRO] servo vs stepper
gyachts
2002-04-03 23:00:01 UTC
Re: servo vs stepper
Jon Elson
2002-04-04 09:24:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
jeffdavis516
2002-04-04 10:39:35 UTC
Re: servo vs stepper
Alan Marconett KM6VV
2002-04-04 11:02:07 UTC
Re: servo vs stepper
jeffdavis516
2002-04-04 11:56:14 UTC
Re: servo vs stepper
Alan Marconett KM6VV
2002-04-04 12:49:08 UTC
Re: servo vs stepper
jeffdavis516
2002-04-04 13:15:03 UTC
Re: servo vs stepper
Tim Goldstein
2002-04-04 14:44:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
jeffdavis516
2002-04-04 15:17:33 UTC
Re: servo vs stepper
Alan Marconett KM6VV
2002-04-04 16:16:23 UTC
Re: servo vs stepper
Jon Elson
2002-04-04 22:30:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Jon Elson
2002-04-04 22:38:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Jon Elson
2002-04-04 22:43:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
jeffdavis516
2002-04-04 22:44:26 UTC
Re: servo vs stepper
Alan Marconett KM6VV
2002-04-05 00:08:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Alan Marconett KM6VV
2002-04-05 00:16:10 UTC
Re: servo vs stepper
Jon Elson
2002-04-05 09:35:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Tim Goldstein
2002-04-06 21:06:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Keith Clark
2004-09-02 06:48:59 UTC
servo vs stepper
R Rogers
2004-09-02 07:29:46 UTC
Re: [CAD_CAM_EDM_DRO] servo vs stepper
Keith Clark
2004-09-02 07:47:42 UTC
Re: servo vs stepper
Bob Muse
2004-09-02 09:48:52 UTC
Re: [CAD_CAM_EDM_DRO] servo vs stepper
turbulatordude
2004-09-02 09:59:33 UTC
Re: servo vs stepper
Keith Clark
2004-09-02 10:29:30 UTC
Re: servo vs stepper
Keith Clark
2004-09-02 10:36:25 UTC
Re: servo vs stepper
R Rogers
2004-09-02 12:28:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Bob Muse
2004-09-02 12:37:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Keith Clark
2004-09-02 13:05:32 UTC
Re: servo vs stepper
Stephen Wille Padnos
2004-09-02 13:49:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Keith Clark
2004-09-02 14:29:15 UTC
Re: servo vs stepper
Bob Muse
2004-09-02 15:06:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Stephen Wille Padnos
2004-09-02 18:07:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Stephen Wille Padnos
2004-09-02 18:27:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Jon Elson
2004-09-02 19:49:59 UTC
Re: [CAD_CAM_EDM_DRO] servo vs stepper
Jon Elson
2004-09-02 23:04:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Jon Elson
2004-09-02 23:11:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Keith Clark
2004-09-03 03:41:46 UTC
Re: servo vs stepper
Keith Clark
2004-09-03 03:45:35 UTC
Re: servo vs stepper
Keith Clark
2004-09-03 03:55:51 UTC
Re: servo vs stepper
Keith Clark
2004-09-03 04:03:01 UTC
Re: servo vs stepper
Keith Clark
2004-09-03 04:04:07 UTC
Re: servo vs stepper
Stephen Wille Padnos
2004-09-03 07:24:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Stephen Wille Padnos
2004-09-03 07:30:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Stephen Wille Padnos
2004-09-03 07:41:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Stephen Wille Padnos
2004-09-03 09:01:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Jon Elson
2004-09-03 09:36:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper
Jon Elson
2004-09-03 09:42:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo vs stepper