CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] EMC

Posted by Ian W. Wright
on 2002-05-09 07:43:53 UTC
Hi Gene,

Sounds like you are trying to make things too complicated...;o)

To use MDI, first hit the F1 key to get the machine out of ESTOP, then hit
the F2 turn it 'ON' so the top two boxes on the screen should now read
'Estop Reset' and 'Machine on'. Good. Now hit the F5 key for MDI mode (F3 is
manual, F4 is auto and F5 is MDI). Type a single command into the MDI window
(like G1x1.5y2.5z0.5F3 or somethinf similar) and then just hit the ENTER key
on the LETTERS part of the keyboard - not the one that says 'enter' but the
big one with the bent arrow on it! This should then make the machine move to
the appropriate place and the figures on the screen should change to reflect
the machine movement.
You can only use the MDI mode for doing single moves although these may be
complex moves in any number of the axes which the program is set up to do.
In the example quoted, assuming you are working in inch measurements, the
table should move smoothly to the left and towards you so that the tool
traces a diagonal path to a point 1.5" right and 2.5" back from its starting
point and either 0.5" above or 0.5" below its starting point in the vertical
direction depending on the way you have programmed the 'Z' axis to move
would be as well to check this first as it can be quite difficult to get the
tool out from 1/2" below the table surface...

Best wishes,
Ian
--

Ian W. Wright
Sheffield, UK
----- Original Message -----
From: "Gene" <capper@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, May 09, 2002 8:36 AM
Subject: [CAD_CAM_EDM_DRO] EMC


> I tried entering code thru the MDI and it typed into the box all right
> but then how do you execute it? when I tried to turn it on again it
> wouldn't work, when I pushed the EMC-run on the desktop the popimage
> came on and then nothing. Will I have to reinstall and loose all my hard
> won settings? Just when I had it running so sweetly. Sigh!!!+
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>

Discussion Thread

Jon Elson 1999-06-06 17:00:33 UTC EMC Fred Proctor 1999-06-09 13:44:23 UTC EMC Mo 1999-06-09 19:07:53 UTC Re: EMC Tim Goldstein 1999-06-09 23:16:54 UTC Re: EMC Tim Goldstein 1999-06-15 20:18:41 UTC Re: EMC Dan Falck 1999-06-16 04:07:23 UTC Re: EMC Ian W. Wright 1999-07-29 13:03:47 UTC Re: EMC chda@x... 1999-10-12 08:48:51 UTC EMC batwings@x... 1999-10-12 00:29:11 UTC Re: EMC Darrell Gehlsen 1999-10-12 10:08:41 UTC Re: EMC Kahl Klemm 1999-11-11 10:16:23 UTC EMC Tim Goldstein 1999-11-21 13:05:08 UTC RE: EMC Karl Klemm 1999-11-21 17:55:11 UTC RE: EMC Tim Goldstein 1999-11-21 18:55:40 UTC RE: EMC Karl Klemm 1999-11-22 08:43:09 UTC RE: EMC hansw 1999-11-22 08:57:30 UTC Re: EMC Tim Goldstein 1999-11-22 09:25:51 UTC Re: EMC James Cullins 2000-04-19 17:24:43 UTC EMC Tim Goldstein 2000-04-19 19:53:13 UTC RE: [CAD_CAM_EDM_DRO] EMC Dan Mauch 2000-04-20 05:59:37 UTC Re: [CAD_CAM_EDM_DRO] EMC James Cullins 2000-04-20 06:28:07 UTC Re: [CAD_CAM_EDM_DRO] EMC Tim Goldstein 2000-04-20 06:34:52 UTC RE: [CAD_CAM_EDM_DRO]DeskNCrt, was: EMC Chris Salter 2000-08-31 08:07:25 UTC EMC Anne Ogborn 2000-10-09 16:45:06 UTC EMC ballendo@y... 2000-10-09 20:10:22 UTC re:EMC Anne Ogborn 2000-10-10 10:31:18 UTC Re: [CAD_CAM_EDM_DRO] re:EMC Anne Ogborn 2000-10-10 10:55:06 UTC Re: [CAD_CAM_EDM_DRO] re:EMC Jon Elson 2000-10-10 12:02:19 UTC Re: [CAD_CAM_EDM_DRO] re:EMC ballendo@y... 2000-10-10 15:23:51 UTC Re: re:EMC Jon Elson 2000-10-10 15:59:44 UTC Re: [CAD_CAM_EDM_DRO] Re: re:EMC ballendo@y... 2000-10-10 16:36:21 UTC Re: Re: re:EMC Tom Caudle 2000-10-10 17:04:19 UTC Re: re:EMC ballendo@y... 2000-10-10 18:02:34 UTC RE:re: EMC Tom Caudle 2000-10-10 18:08:41 UTC Re: RE:re: EMC dave engvall 2000-10-10 18:11:59 UTC Re: [CAD_CAM_EDM_DRO] RE:re: EMC Anne Ogborn 2000-10-10 19:15:14 UTC Re: [CAD_CAM_EDM_DRO] Re: re:EMC Anne Ogborn 2000-10-10 19:24:24 UTC Re: [CAD_CAM_EDM_DRO] RE:re: EMC ballendo@y... 2000-10-10 19:27:08 UTC re:RE: EMC Tom Caudle 2000-10-10 19:47:22 UTC Re: re:EMC Anne Ogborn 2000-10-10 21:44:53 UTC Re: [CAD_CAM_EDM_DRO] Re: re:EMC catboat15@a... 2000-10-11 09:40:45 UTC Re: [CAD_CAM_EDM_DRO] Re: re:EMC ballendo@y... 2000-10-11 20:53:09 UTC re:Re:rE:RE: EMC barker1@m... 2000-11-03 05:11:59 UTC EMC Dan Falck 2000-11-03 05:29:18 UTC Re: [CAD_CAM_EDM_DRO] EMC Tim Goldstein 2000-11-03 09:10:56 UTC RE: [CAD_CAM_EDM_DRO] EMC Jon Elson 2000-11-03 12:08:09 UTC Re: [CAD_CAM_EDM_DRO] EMC Scott Hendershot 2002-03-28 10:48:22 UTC EMC j.guenther 2002-03-28 11:11:32 UTC RE: [CAD_CAM_EDM_DRO] EMC Tim Goldstein 2002-03-28 11:13:06 UTC Re: [CAD_CAM_EDM_DRO] EMC Kos 2002-03-28 12:25:40 UTC Re: EMC Paul 2002-03-28 12:32:25 UTC Re: [CAD_CAM_EDM_DRO] EMC Scott Hendershot 2002-03-28 14:14:31 UTC Re: [CAD_CAM_EDM_DRO] EMC Tim Goldstein 2002-03-28 15:04:41 UTC Re: [CAD_CAM_EDM_DRO] EMC William Scalione 2002-03-28 21:43:04 UTC Re: [CAD_CAM_EDM_DRO] EMC Jon Elson 2002-03-28 22:25:04 UTC Re: [CAD_CAM_EDM_DRO] EMC Bill Vance 2002-03-28 23:14:09 UTC Re: [CAD_CAM_EDM_DRO] EMC Darrell Daniels 2002-03-28 23:26:40 UTC Re: [CAD_CAM_EDM_DRO] EMC Darrell Daniels 2002-03-28 23:31:42 UTC Re: [CAD_CAM_EDM_DRO] EMC Gene 2002-05-06 13:10:29 UTC EMC Tim Goldstein 2002-05-06 14:39:30 UTC Re: [CAD_CAM_EDM_DRO] EMC Ray Henry 2002-05-06 21:09:41 UTC Re: EMC Jon Elson 2002-05-06 22:05:51 UTC Re: [CAD_CAM_EDM_DRO] EMC Gene 2002-05-07 15:18:50 UTC EMC Gene 2002-05-09 00:36:24 UTC EMC Ian W. Wright 2002-05-09 07:43:53 UTC Re: [CAD_CAM_EDM_DRO] EMC Gene 2002-05-09 10:32:03 UTC EMC Jon Elson 2002-05-09 22:30:55 UTC Re: [CAD_CAM_EDM_DRO] EMC Gene 2002-05-26 20:20:00 UTC EMC Jon Elson 2002-05-26 23:21:03 UTC Re: [CAD_CAM_EDM_DRO] EMC IMService 2002-06-06 06:14:50 UTC Re: EMC Gene 2002-08-18 16:07:21 UTC EMC John Guenther 2002-08-18 19:48:08 UTC RE: [CAD_CAM_EDM_DRO] EMC Jon Elson 2002-08-18 20:34:54 UTC Re: [CAD_CAM_EDM_DRO] EMC dakota8833 2002-08-23 05:12:23 UTC EMC Tom Benedict 2002-08-23 08:15:46 UTC Re: [CAD_CAM_EDM_DRO] EMC Ray Henry 2002-08-23 14:50:49 UTC Re: EMC Les Watts 2002-08-23 15:28:41 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Gene 2002-11-18 21:30:53 UTC EMC Jon Elson 2002-11-19 21:04:40 UTC Re: [CAD_CAM_EDM_DRO] EMC Gene 2002-11-19 21:16:30 UTC Re: [CAD_CAM_EDM_DRO] EMC Tim Goldstein 2002-11-19 21:57:45 UTC RE: [CAD_CAM_EDM_DRO] EMC Matt Shaver 2002-11-19 22:14:29 UTC Re: [CAD_CAM_EDM_DRO] EMC William Scalione 2002-11-19 23:00:43 UTC Re: [CAD_CAM_EDM_DRO] EMC Tim Goldstein 2002-11-19 23:30:51 UTC RE: [CAD_CAM_EDM_DRO] EMC Jon Elson 2002-11-20 10:29:21 UTC Re: [CAD_CAM_EDM_DRO] EMC Yesamazza@a... 2003-02-08 09:09:21 UTC EMC William Scalione 2003-02-08 09:34:15 UTC Re: [CAD_CAM_EDM_DRO] EMC Vince Negrete 2003-09-15 03:25:04 UTC EMC Gene 2004-08-06 16:17:38 UTC EMC