CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper

Posted by Jon Elson
on 2002-09-16 21:42:39 UTC
Erik Reikes wrote:

> Because of the odd shapes of the pieces I was using I had been boring
> my bearing seats with a boring head in my mill. My biggest problems
> with tight tolerances really have been tool deflection and the fact
> that I don't have guage blocks or even a real internal micrometer.

I have a set of 5 (or maybe 6) telescoping gauges. They can be held inside
a hole and allowed to expand to the diameter. You then tighten the clamp
knob slightly and wiggle the handle around in the bore until you feel that
the springs have brought the tips to the true diameter, then you tighten the
knob fully and swing it off-axis a bit to allow it to be pulled out. then you
measure it with a micrometer. This works pretty well, but when getting close
to final diamater, i usually take the measurement 2 or 3 times to be sure I have
a consistant reading. These are a LOT cheaper than a set of internal
mikes.

Jon

Discussion Thread

turbulatordude 2002-09-11 14:13:04 UTC stuck stepper Scot R. Darr 2002-09-11 14:35:26 UTC RE: [CAD_CAM_EDM_DRO] stuck stepper JanRwl@A... 2002-09-11 14:55:28 UTC Re: [CAD_CAM_EDM_DRO] stuck stepper Michael Holm 2002-09-11 16:24:03 UTC Re: [CAD_CAM_EDM_DRO] stuck stepper turbulatordude 2002-09-11 17:42:31 UTC Re: stuck stepper Brian 2002-09-11 19:10:02 UTC Re: [CAD_CAM_EDM_DRO] stuck stepper JanRwl@A... 2002-09-11 19:42:42 UTC Re: [CAD_CAM_EDM_DRO] stuck stepper JanRwl@A... 2002-09-11 19:49:08 UTC Re: [CAD_CAM_EDM_DRO] Re: stuck stepper turbulatordude 2002-09-12 06:10:01 UTC Bad Bearing ( was Re: stuck stepper turbulatordude 2002-09-12 13:47:11 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper markpowerplus 2002-09-12 14:38:20 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Les Watts 2002-09-12 15:04:10 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper galt1x 2002-09-12 15:17:47 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper turbulatordude 2002-09-12 16:02:25 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Raymond Heckert 2002-09-12 16:49:04 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Les Watts 2002-09-12 17:10:47 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper turbulatordude 2002-09-13 06:23:27 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Erik Reikes 2002-09-13 11:10:54 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper turbulatordude 2002-09-13 17:56:46 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Les Watts 2002-09-13 18:24:30 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper bjammin@i... 2002-09-14 05:25:11 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Erik Reikes 2002-09-15 11:26:58 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Peter 2002-09-15 14:44:51 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Doug Harrison 2002-09-15 15:48:21 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper bjammin@i... 2002-09-16 06:06:01 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Erik Reikes 2002-09-16 13:13:59 UTC Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper bjammin@i... 2002-09-16 14:11:32 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper Jon Elson 2002-09-16 21:42:39 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper bjammin@i... 2002-09-17 04:40:35 UTC Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper