Re: stuck stepper
Posted by
turbulatordude
on 2002-09-11 17:42:31 UTC
If there are wires touching, they must be internal.
The unit was mounted in some oil or other liquid. it had a seal on
the shaft.
There is some slight play with about 15 degess of motion in one spot
so I assume that it might be physical and not electronical.
Dave
The unit was mounted in some oil or other liquid. it had a seal on
the shaft.
There is some slight play with about 15 degess of motion in one spot
so I assume that it might be physical and not electronical.
Dave
--- In CAD_CAM_EDM_DRO@y..., "Scot R. Darr" <scot@c...> wrote:
> Are any of the wires touching when you try to spin it? My Vexta
steppers are nearly impossible to spin if some of the leads are
touching each other. When I separate them they feel fine.
>
> -----Original Message-----
> From: turbulatordude [mailto:davemucha@j...]
> Sent: Wednesday, September 11, 2002 3:13 PM
> To: CAD_CAM_EDM_DRO@y...
> Subject: [CAD_CAM_EDM_DRO] stuck stepper
>
>
> Hi all,
>
> I am trying to test my latest set-up and found one of my e-bay
steppers
> is locked up.
>
> NEMA34 single stack, and I have a tough time spinning it by hand.
> It's one of those high tech manufacturers, ASTROSYN !
> (yeah, I never heard of them before either)
> Minebea Co. Ltd, Thailand
>
> 1.7 V, 4.7 A and in series mode, my Gecko can get it to spin at
about
> 100 to 200 er.... 0.1 to 0.2 hertz
>
> Iwant to open it up and look at the bearings, but am not sure if I
am
> better off trashing it and getting a new one, or trying to fix this
> one.
>
> looking for recommendations.
>
> Dave
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach
it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as
a sister site to the CCED group, as many of the same members are
there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>
> Post messages: CAD_CAM_EDM_DRO@y...
> Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> Moderator: jmelson@a... timg@k... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
Discussion Thread
turbulatordude
2002-09-11 14:13:04 UTC
stuck stepper
Scot R. Darr
2002-09-11 14:35:26 UTC
RE: [CAD_CAM_EDM_DRO] stuck stepper
JanRwl@A...
2002-09-11 14:55:28 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
Michael Holm
2002-09-11 16:24:03 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
turbulatordude
2002-09-11 17:42:31 UTC
Re: stuck stepper
Brian
2002-09-11 19:10:02 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
JanRwl@A...
2002-09-11 19:42:42 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
JanRwl@A...
2002-09-11 19:49:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: stuck stepper
turbulatordude
2002-09-12 06:10:01 UTC
Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-12 13:47:11 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
markpowerplus
2002-09-12 14:38:20 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Les Watts
2002-09-12 15:04:10 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
galt1x
2002-09-12 15:17:47 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-12 16:02:25 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Raymond Heckert
2002-09-12 16:49:04 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Les Watts
2002-09-12 17:10:47 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-13 06:23:27 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Erik Reikes
2002-09-13 11:10:54 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-13 17:56:46 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Les Watts
2002-09-13 18:24:30 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-14 05:25:11 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Erik Reikes
2002-09-15 11:26:58 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Peter
2002-09-15 14:44:51 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Doug Harrison
2002-09-15 15:48:21 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-16 06:06:01 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Erik Reikes
2002-09-16 13:13:59 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-16 14:11:32 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Jon Elson
2002-09-16 21:42:39 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-17 04:40:35 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper