Re: [CAD_CAM_EDM_DRO] stuck stepper
Posted by
JanRwl@A...
on 2002-09-11 14:55:28 UTC
Dave: Without SEEING it myself, I would guess that there is magnetic swarf
between the rotor and stator "teeth" inside. The "gap" between those is just
a few mils, so a "tiny" chip of that hard magnetic stuff can jam things.
It is a "no-no" to dismantle a stepper (because THIS happens!), but if it
ain't no good, no-how, then carefully remove the four screws, pull it apart,
blow off the swarf with 100 psi blow-gun with an OSHA-DISapproved tip, and
try slipping it back together with maybe some stiff paper wrapped around the
rotor, to prevent "banging" and chipping. Then, slip that paper out when you
JUST-can't get your fingers or tweezers "in there" anymore, and re-assemble.
It's a learning project, at least!
Let us know if this worked!
Jan Rowland, Ignernt old Troll
[Non-text portions of this message have been removed]
between the rotor and stator "teeth" inside. The "gap" between those is just
a few mils, so a "tiny" chip of that hard magnetic stuff can jam things.
It is a "no-no" to dismantle a stepper (because THIS happens!), but if it
ain't no good, no-how, then carefully remove the four screws, pull it apart,
blow off the swarf with 100 psi blow-gun with an OSHA-DISapproved tip, and
try slipping it back together with maybe some stiff paper wrapped around the
rotor, to prevent "banging" and chipping. Then, slip that paper out when you
JUST-can't get your fingers or tweezers "in there" anymore, and re-assemble.
It's a learning project, at least!
Let us know if this worked!
Jan Rowland, Ignernt old Troll
[Non-text portions of this message have been removed]
Discussion Thread
turbulatordude
2002-09-11 14:13:04 UTC
stuck stepper
Scot R. Darr
2002-09-11 14:35:26 UTC
RE: [CAD_CAM_EDM_DRO] stuck stepper
JanRwl@A...
2002-09-11 14:55:28 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
Michael Holm
2002-09-11 16:24:03 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
turbulatordude
2002-09-11 17:42:31 UTC
Re: stuck stepper
Brian
2002-09-11 19:10:02 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
JanRwl@A...
2002-09-11 19:42:42 UTC
Re: [CAD_CAM_EDM_DRO] stuck stepper
JanRwl@A...
2002-09-11 19:49:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: stuck stepper
turbulatordude
2002-09-12 06:10:01 UTC
Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-12 13:47:11 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
markpowerplus
2002-09-12 14:38:20 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Les Watts
2002-09-12 15:04:10 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
galt1x
2002-09-12 15:17:47 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-12 16:02:25 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Raymond Heckert
2002-09-12 16:49:04 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Les Watts
2002-09-12 17:10:47 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-13 06:23:27 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Erik Reikes
2002-09-13 11:10:54 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
turbulatordude
2002-09-13 17:56:46 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Les Watts
2002-09-13 18:24:30 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-14 05:25:11 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Erik Reikes
2002-09-15 11:26:58 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Peter
2002-09-15 14:44:51 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Doug Harrison
2002-09-15 15:48:21 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-16 06:06:01 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Erik Reikes
2002-09-16 13:13:59 UTC
Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-16 14:11:32 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
Jon Elson
2002-09-16 21:42:39 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper
bjammin@i...
2002-09-17 04:40:35 UTC
Re: [CAD_CAM_EDM_DRO] Roller Bearings link ? ( was Bad Bearing ( was Re: stuck stepper