CAD CAM EDM DRO - Yahoo Group Archive

Re: Transformer question

Posted by eissej143
on 2002-10-26 22:49:20 UTC
Pls be careful of your connections. Bear in mind that it's harmful
dealing with current . . . no TRIAL & ERROR for this . . . if ur not
familiar bring it to ur nearest service center . . . no jokes! jc


--- In CAD_CAM_EDM_DRO@y..., "Carol & Jerry Jankura"
<jerry.jankura@s...> wrote:
> Hi, JJ:
>
> I've not heard of a transformer with a center tapped primary.
>
> If, indeed, the primary is center tapped, use only the full winding
at the
> higher voltage or either half of the winding at the lower voltate.
Leave the
> unused end 'floating,' do NOT tie the two outside wires together.
>
> Now, if what you have is actually two windings (four wires) that
can be set
> up as either 120 or 240 volts, that's a different matter. In that
case, you
> tie the two 'bottom' ends together and the two upper ends together
for 120
> volt operation, or you tie the hi end of one to the low end of the
other
> and use the two outside wires for 240 volt operation.
>
> -- Jerry
>
>
> |-----Original Message-----
> |From: JJ [mailto:jj5412@e...]
> |Sent: Tuesday, October 01, 2002 6:12 PM
> |To: cad_cam_edm_dro@y...
> |Subject: [CAD_CAM_EDM_DRO] Transformer question
> |
> |
> |Okay, my turn for a power supply question.
> |My transformer has a center tapped primary, 110v/220v. Do I
connect the
> |two outer legs together and use them with the center tap for 110v?
Or
> |use it half-coil <g> and use one leg and the center tap.
> |
> |ADVthanksANCE,
> | JJ
> |
> |Be Kind, Be Careful, Be Yourself
> |
> |
> |
> |Addresses:
> |FAQ: http://www.ktmarketing.com/faq.html
> |FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> |
> |OFF Topic POSTS: General Machining
> |If you wish to post on unlimited OT subjects goto:
> |aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> |reach it if you have trouble.
> |http://www.metalworking.com/news_servers.html
> |
> |http://groups.yahoo.com/group/jobshophomeshop I consider this as
> |a sister site to the CCED group, as many of the same members are
> |there, for OT subjects, that are not allowed on the CCED list.
> |
> |NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> |THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
EXCEPTIONS........
> |
> |Post messages: CAD_CAM_EDM_DRO@y...
> |Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> |Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> |List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> |Moderator: jmelson@a... timg@k... [Moderator]
> |URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> |bill,
> |List Mom
> |List Owner
> |
> |
> |
> |Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> |
> |
> |

Discussion Thread

Joe Vicars 2001-01-12 05:31:42 UTC Transformer question Jon Elson 2001-01-12 11:45:08 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Dick Ganderton 2001-01-12 15:58:28 UTC Re: [CAD_CAM_EDM_DRO] Transformer question JanRwl@A... 2001-01-12 20:01:01 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Ray 2001-01-12 20:12:38 UTC Re: Transformer question Jon Elson 2001-01-12 22:57:41 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Jon Elson 2001-01-12 23:15:57 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Roman Black 2001-01-13 09:06:54 UTC Re: Transformer question Hugh Prescott 2001-01-13 10:44:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Transformer question Tom Caudle 2001-01-13 18:52:34 UTC Re: Transformer question Tom 2001-10-29 15:18:18 UTC Transformer question JanRwl@A... 2001-10-29 19:31:43 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Jon Elson 2001-10-29 21:31:59 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Carol & Jerry Jankura 2001-10-30 05:55:58 UTC RE: [CAD_CAM_EDM_DRO] Transformer question Ray 2001-10-30 06:53:34 UTC Re: Transformer question tcsibor@v... 2001-10-30 11:27:32 UTC Re: Transformer question Andre' Blanchard 2001-10-30 14:26:15 UTC Re: Transformer question JanRwl@A... 2001-10-30 18:11:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Transformer question Ray 2001-10-31 12:47:16 UTC Re: Re: Re: Transformer question JJ 2002-10-01 16:12:47 UTC Transformer question mariss92705 2002-10-01 16:27:54 UTC Re: Transformer question JJ 2002-10-01 16:29:57 UTC RE: [CAD_CAM_EDM_DRO] Re: Transformer question Raymond Heckert 2002-10-01 17:14:39 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Carol & Jerry Jankura 2002-10-01 18:18:50 UTC RE: [CAD_CAM_EDM_DRO] Transformer question JJ 2002-10-02 16:15:18 UTC RE: [CAD_CAM_EDM_DRO] Transformer question eissej143 2002-10-26 22:49:20 UTC Re: Transformer question Tom Murray 2002-11-19 09:04:16 UTC Transformer question aussiedude 2002-11-19 09:36:53 UTC RE: [CAD_CAM_EDM_DRO] Transformer question turbulatordude 2002-11-19 19:14:42 UTC Re: Transformer question JanRwl@A... 2002-11-19 19:23:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Transformer question JanRwl@A... 2002-11-19 20:02:00 UTC Re: [CAD_CAM_EDM_DRO] Transformer question Raymond Heckert 2002-11-20 16:26:58 UTC Re: [CAD_CAM_EDM_DRO] Transformer question