Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
Posted by
Steven Ciciora
on 2003-08-20 09:35:40 UTC
I didn't look up your model number, but all the CompuMotor stuff I had
could not be directly driven from a parallel port. Since the input of my
CompuMotor stuff are opto-isolators, my parallel ports couldn't drive
enough current. I wired up a buffer circuit. After finishing it, I saw
the PMX-120 (I think the correct part number) breakout board, and almost
bought it to replace what I had just finished, it was so nice. I would
recommend checking this out.
- Steven Ciciora
could not be directly driven from a parallel port. Since the input of my
CompuMotor stuff are opto-isolators, my parallel ports couldn't drive
enough current. I wired up a buffer circuit. After finishing it, I saw
the PMX-120 (I think the correct part number) breakout board, and almost
bought it to replace what I had just finished, it was so nice. I would
recommend checking this out.
- Steven Ciciora
><snip>
>Hence the big bucks for MasterCAM and such. Do you have suggestions?
>When all of this comes together it will go on a small mill. Is there
>additional hardware needed to connect to the PC? I would expect that
>different pins would control different axis's up to a limited number
>without additional hardware.
>
>Randy
Discussion Thread
m0nkey0ne
2003-08-15 22:38:04 UTC
M57-102 < - - - - > PC
turbulatordude
2003-08-16 09:11:59 UTC
Re: M57-102 < - - - - > PC
Mon Wan
2003-08-16 19:28:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
Jon Elson
2003-08-16 22:34:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
m0nkey0ne
2003-08-17 10:57:56 UTC
Re: M57-102 < - - - - > PC
Jon Elson
2003-08-17 14:42:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
Bob McIlvaine
2003-08-17 17:09:55 UTC
Lindows?
David A. Frantz
2003-08-17 20:20:12 UTC
Re: [CAD_CAM_EDM_DRO] Lindows?
Matt Shaver
2003-08-17 21:12:55 UTC
Re: [CAD_CAM_EDM_DRO] Lindows?
Lloyd Leung
2003-08-17 21:27:30 UTC
RE: Lindows?
Tim Goldstein
2003-08-17 21:28:22 UTC
RE: [CAD_CAM_EDM_DRO] Lindows?
Tim Goldstein
2003-08-17 21:32:00 UTC
Off list: RE: Lindows?
Paul
2003-08-18 11:33:52 UTC
Re: [CAD_CAM_EDM_DRO] RE: Lindows?
m0nkey0ne
2003-08-19 09:25:04 UTC
Re: M57-102 < - - - - > PC
Jon Elson
2003-08-19 10:38:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
m0nkey0ne
2003-08-20 09:21:11 UTC
Re: M57-102 < - - - - > PC
Steven Ciciora
2003-08-20 09:35:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
William Scalione
2003-08-20 17:40:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
m0nkey0ne
2003-08-22 22:10:10 UTC
Re: M57-102 < - - - - > PC
m0nkey0ne
2003-08-23 00:58:41 UTC
Re: M57-102 < - - - - > PC
Jon Elson
2003-08-23 12:22:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC
m0nkey0ne
2003-08-27 19:58:15 UTC
Re: M57-102 < - - - - > PC
Jon Elson
2003-08-27 22:37:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: M57-102 < - - - - > PC