Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
Posted by
Terrenoire, Adrien L
on 2005-01-26 07:00:14 UTC
You can use multiple caps in parallel if needed.
-----Original Message-----
From: R Rogers <rogersmach@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wed Jan 26 09:56:14 2005
Subject: Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
"A. G. Eckstein" <a_eckstein@...> wrote:
Rick,
Mariss has a formula that is conservative, and WORKS:
C=80000 x I/E where C is in microFarads, I is in Amps, and E is in Volts
So in your case, I would look at 80000*12/70 or 13714µF and round up to the
next highest value with a voltage rating of at least 100V
/// Is this per drive though? I have servos and I'm using 3-100 volt caps at 15,000 uF each. Marriss said I needed one rated at 100 volt and 45k uF Which is very difficult to find. Does anyone know where a Cap that size can be purchased? Or close to it?
Ron
[Non-text portions of this message have been removed]
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
-----------------------------------------
The information contained in this transmission may contain privileged and confidential information and is intended only for the use of the person(s) named above. If you are not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, any review, dissemination, distribution or duplication of this communication is strictly prohibited. If you are not the intended recipient, please contact the sender immediately by reply e-mail and destroy all copies of the original message. Please note that we do not accept account orders and/or instructions by e-mail, and therefore will not be responsible for carrying out such orders and/or instructions.
If you, as the intended recipient of this message, the purpose of which is to inform and update our clients, prospects and consultants of developments relating to our services and products, would not like to receive further e-mail correspondence from the sender, please "reply" to the sender indicating your wishes. In the U.S.: 1345 Avenue of the Americas, New York, NY 10105.
-----Original Message-----
From: R Rogers <rogersmach@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wed Jan 26 09:56:14 2005
Subject: Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
"A. G. Eckstein" <a_eckstein@...> wrote:
Rick,
Mariss has a formula that is conservative, and WORKS:
C=80000 x I/E where C is in microFarads, I is in Amps, and E is in Volts
So in your case, I would look at 80000*12/70 or 13714µF and round up to the
next highest value with a voltage rating of at least 100V
/// Is this per drive though? I have servos and I'm using 3-100 volt caps at 15,000 uF each. Marriss said I needed one rated at 100 volt and 45k uF Which is very difficult to find. Does anyone know where a Cap that size can be purchased? Or close to it?
Ron
[Non-text portions of this message have been removed]
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
-----------------------------------------
The information contained in this transmission may contain privileged and confidential information and is intended only for the use of the person(s) named above. If you are not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, any review, dissemination, distribution or duplication of this communication is strictly prohibited. If you are not the intended recipient, please contact the sender immediately by reply e-mail and destroy all copies of the original message. Please note that we do not accept account orders and/or instructions by e-mail, and therefore will not be responsible for carrying out such orders and/or instructions.
If you, as the intended recipient of this message, the purpose of which is to inform and update our clients, prospects and consultants of developments relating to our services and products, would not like to receive further e-mail correspondence from the sender, please "reply" to the sender indicating your wishes. In the U.S.: 1345 Avenue of the Americas, New York, NY 10105.
Discussion Thread
rllalonde2000
2005-01-26 04:28:01 UTC
What size capacitor should I use?
A. G. Eckstein
2005-01-26 04:58:31 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
Simon Arthur
2005-01-26 05:38:23 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
R Rogers
2005-01-26 06:56:31 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
Terrenoire, Adrien L
2005-01-26 07:00:14 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
Andy Wander
2005-01-26 07:01:23 UTC
RE: [CAD_CAM_EDM_DRO] What size capacitor should I use?
turbulatordude
2005-01-26 07:07:50 UTC
Re: What size capacitor should I use? - voltage ?
A. G. Eckstein
2005-01-26 07:13:30 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
caudlet
2005-01-26 08:00:51 UTC
Re: What size capacitor should I use?
Bengt
2005-01-26 09:11:26 UTC
Re: What size capacitor should I use?
Jon Elson
2005-01-26 09:28:27 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
Roy J. Tellason
2005-01-26 09:44:34 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
turbulatordude
2005-01-26 09:58:26 UTC
Re: What size capacitor should I use?
Andy Wander
2005-01-26 10:19:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
caudlet
2005-01-26 11:29:56 UTC
Re: What size capacitor should I use?
Roy J. Tellason
2005-01-26 11:41:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
Rob Polley
2005-01-26 11:43:12 UTC
Looking for advice
Dan Mauch
2005-01-26 12:18:29 UTC
Re: [CAD_CAM_EDM_DRO] Looking for advice
Codesuidae
2005-01-26 12:34:15 UTC
Re: [CAD_CAM_EDM_DRO] Looking for advice
victorlorenzo@y...
2005-01-26 12:55:47 UTC
Re: Looking for advice
Stephen Wille Padnos
2005-01-26 13:38:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
John
2005-01-26 14:04:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
Simon Arthur
2005-01-26 14:09:40 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
erie
2005-01-26 14:33:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
Stephen Wille Padnos
2005-01-26 14:37:28 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
R Rogers
2005-01-26 14:56:53 UTC
[CAD_CAM_EDM_DRO] Toroidal transformer ratings?? Amps? Kv? Kva?
JanRwl@A...
2005-01-26 15:04:42 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
Les Newell
2005-01-26 15:05:07 UTC
Re: [CAD_CAM_EDM_DRO] Toroidal transformer ratings?? Amps? Kv? Kva?
cnc_4_me
2005-01-26 15:08:24 UTC
Re: What size capacitor should I use?
David Paulson
2005-01-26 15:10:21 UTC
Re: [CAD_CAM_EDM_DRO] Toroidal transformer ratings?? Amps? Kv? Kva?
cnc_4_me
2005-01-26 15:23:15 UTC
Re: Toroidal transformer ratings?? Amps? Kv? Kva?
JanRwl@A...
2005-01-26 15:40:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
R Rogers
2005-01-26 15:49:48 UTC
Re: [CAD_CAM_EDM_DRO] Toroidal transformer ratings?? What after being rectified?
cnc_4_me
2005-01-26 15:55:58 UTC
Re: What size capacitor should I use?
cnc_4_me
2005-01-26 16:14:14 UTC
Re: Toroidal transformer ratings?? What after being rectified?
R Rogers
2005-01-26 16:18:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?sizing supply
Ron Ginger
2005-01-26 17:01:36 UTC
Re: Looking for advice
polaraligned
2005-01-26 17:09:38 UTC
What size capacitor should I use?
Polaraligned
2005-01-26 17:25:09 UTC
Re: Toroidal transformer ratings?? Amps? Kv? Kva?
R Rogers
2005-01-26 17:29:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for advice
cnc_4_me
2005-01-26 18:05:05 UTC
Re: What size capacitor should I use?
victorlorenzo@y...
2005-01-26 18:19:00 UTC
Re: Looking for advice
codeSuidae
2005-01-26 18:32:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
cnc_4_me
2005-01-26 18:54:06 UTC
Re: What size capacitor should I use?
Ken Langston
2005-01-26 18:56:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? Amps? Kv? Kva?
cnc_4_me
2005-01-26 19:01:47 UTC
Re: Toroidal transformer ratings?? Amps? Kv? Kva?
Rob Polley
2005-01-26 19:24:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for advice
codeSuidae
2005-01-26 19:26:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
cnc_4_me
2005-01-26 19:35:49 UTC
Re: Looking for advice
bobmcknight@c...
2005-01-26 19:37:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? Amps? Kv? Kva?
bobmcknight@c...
2005-01-26 19:37:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
cnc_4_me
2005-01-26 19:54:55 UTC
Re: What size capacitor should I use?
turbulatordude
2005-01-26 19:57:22 UTC
Re: What size capacitor should I use? resistors....
cnc_4_me
2005-01-26 20:08:00 UTC
Re: What size capacitor should I use? resistors....
JanRwl@A...
2005-01-26 21:34:22 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
JanRwl@A...
2005-01-26 21:43:19 UTC
Re: [CAD_CAM_EDM_DRO] Toroidal transformer ratings?? Amps? Kv? Kva?
codeSuidae
2005-01-26 21:56:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
Jon Elson
2005-01-26 21:56:33 UTC
Re: [CAD_CAM_EDM_DRO] Toroidal transformer ratings?? What after being rectified?
Mariss Freimanis
2005-01-26 21:58:04 UTC
Re: What size capacitor should I use? resistors....
Jon Elson
2005-01-26 22:08:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use?
JanRwl@A...
2005-01-26 22:09:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for advice
Jon Elson
2005-01-26 22:22:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? Amps? Kv? Kva?
Jon Elson
2005-01-26 22:29:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use? resistors....
Jon Elson
2005-01-26 22:33:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use? resistors....
Simon Arthur
2005-01-27 00:01:53 UTC
Re: [CAD_CAM_EDM_DRO] What size capacitor should I use?
Polaraligned
2005-01-27 04:15:31 UTC
Re: What size capacitor should I use?
Polaraligned
2005-01-27 04:29:29 UTC
Re: Toroidal transformer ratings?? What after being rectified?
turbulatordude
2005-01-27 06:26:30 UTC
Re: What size capacitor should I use? resistor or not ??
turbulatordude
2005-01-27 06:45:41 UTC
Re: Toroidal transformer ratings?? What after being rectified?
Leslie Watts
2005-01-27 07:04:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? What after being rectified?
Jon Elson
2005-01-27 10:30:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? What after being rectified?
Jon Elson
2005-01-27 10:40:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: What size capacitor should I use? resistor or not ??
cnc_4_me
2005-01-27 10:47:17 UTC
Re: Toroidal transformer ratings?? What after being rectified?
Les Newell
2005-01-27 12:49:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? What after being rectified?
Polaraligned
2005-01-27 13:39:18 UTC
Re: Toroidal transformer ratings?? What after being rectified?
Stephen Wille Padnos
2005-01-27 14:44:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? What after being rectified?
Polaraligned
2005-01-27 18:13:16 UTC
Re: Toroidal transformer ratings?? What after being rectified?
Steve Stallings
2005-01-27 18:18:44 UTC
Re: Toroidal transformer ratings?? What after being rectified?
Stephen Wille Padnos
2005-01-27 18:28:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? What after being rectified?
Jon Elson
2005-01-27 21:35:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? What after being rectified?
Kevin Martin
2005-01-28 05:32:28 UTC
RE: [CAD_CAM_EDM_DRO] Re: Toroidal transformer ratings?? What after being rectified?
m0nkey0ne
2005-01-28 11:22:47 UTC
Re: Toroidal transformer ratings?? What after being rectified?
Mcginnis, Darrell S
2005-03-22 14:43:20 UTC
RE: [CAD_CAM_EDM_DRO] What size capacitor should I use?