Re: linear bearing based on ground flat stock
Posted by
Graham Stabler
on 2006-05-22 12:19:12 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@... wrote:
not that I don't have the cash it is just that I don't want to spend
it on this project, this will be a fun and super fast machine to show
what's possible. It will mill foam and wax but not much else.
I have some ideas for a ceiling mounted huge one as well but I have no
where to build it so its a mute point really but it involves bicycle
hubs, lots of skate bearings and some carbon fibre tube :O
Graham
>over" debris
>
> In a message dated 5/22/2006 12:21:50 A.M. Mountain Daylight Time,
> JanRwl@... writes:
>
> The "V-groove" system they use is much better
> than a flat roller on a flat surface, as the latter will "bump
> andV-groove
> won't run smooth for long, before needing cleaning, while the
> stuffon the
> is pretty-much self-cleaning as it rolls.
>
>
>
> If you are short of cash, make a close fitting sleeve with a V grove
> outside, and LocTite it to the bearing, or bushing. Be careful tonot get
> any LocTite into the bearing.I would still need something for my cheap v-rollers to run on. Its
> bill
>
>
> [Non-text portions of this message have been removed]
>
not that I don't have the cash it is just that I don't want to spend
it on this project, this will be a fun and super fast machine to show
what's possible. It will mill foam and wax but not much else.
I have some ideas for a ceiling mounted huge one as well but I have no
where to build it so its a mute point really but it involves bicycle
hubs, lots of skate bearings and some carbon fibre tube :O
Graham
Discussion Thread
Graham Stabler
2006-05-21 13:11:26 UTC
linear bearing based on ground flat stock
Jack Hudler
2006-05-21 15:42:03 UTC
RE: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock
Graham Stabler
2006-05-21 17:40:00 UTC
Re: linear bearing based on ground flat stock
Aftiel
2006-05-21 18:56:59 UTC
Re: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock
Jack Hudler
2006-05-21 19:53:32 UTC
RE: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock
Jack Hudler
2006-05-21 20:23:45 UTC
RE: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock
JanRwl@A...
2006-05-21 23:20:43 UTC
Re: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock
ballendo
2006-05-22 02:10:28 UTC
Re: linear bearing based on ground flat stock
Les Newell
2006-05-22 02:28:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
ballendo
2006-05-22 02:38:27 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-22 03:24:39 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-22 03:27:07 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-22 03:37:54 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 04:07:14 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 04:12:34 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 04:19:13 UTC
Re: linear bearing based on ground flat stock
tomp-tag
2006-05-22 06:27:51 UTC
Re: linear bearing based on ground flat stock
Jack Hudler
2006-05-22 11:03:57 UTC
RE: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
wanliker@a...
2006-05-22 11:07:17 UTC
Re: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock
Graham Stabler
2006-05-22 12:12:12 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-22 12:19:12 UTC
Re: linear bearing based on ground flat stock
wanliker@a...
2006-05-22 12:30:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
wanliker@a...
2006-05-22 12:37:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-22 12:59:33 UTC
Re: linear bearing based on ground flat stock
wanliker@a...
2006-05-22 13:20:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
ballendo
2006-05-22 14:49:37 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 15:10:31 UTC
Re: linear bearing based on ground flat stock
wanliker@a...
2006-05-22 15:33:21 UTC
linear bearing based on ground flat stock
Jack Hudler
2006-05-22 15:39:38 UTC
RE: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
turbulatordude
2006-05-22 17:57:06 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-22 18:07:59 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-22 18:09:55 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 20:04:04 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 20:06:24 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 20:12:47 UTC
Re: linear bearing based on ground flat stock
turbulatordude
2006-05-22 20:52:13 UTC
Re: linear bearing based on ground flat stock
JanRwl@A...
2006-05-22 22:00:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
wanliker@a...
2006-05-22 22:17:59 UTC
linear bearing based on ground flat stock
ballendo
2006-05-22 22:35:03 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-22 22:44:35 UTC
Re: linear bearing based on ground flat stock
wthomas@g...
2006-05-22 23:25:58 UTC
W.E.T. [CAD_CAM_EDM_DRO] Rd bearing based on ground Drill Rod
Graham Stabler
2006-05-23 03:23:00 UTC
Re: linear bearing based on ground flat stock
Fred Smith
2006-05-23 07:10:50 UTC
Re: linear bearing based on ground flat stock
turbulatordude
2006-05-23 09:08:10 UTC
Re: linear bearing based on ground flat stock
Fred Smith
2006-05-23 09:28:44 UTC
Re: linear bearing based on ground flat stock
turbulatordude
2006-05-23 10:37:42 UTC
Re: linear bearing based on ground flat stock
ballendo
2006-05-23 14:43:24 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-23 16:09:18 UTC
Re: linear bearing based on ground flat stock
Blue
2006-05-23 18:06:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-24 02:50:27 UTC
Re: linear bearing based on ground flat stock
turbulatordude
2006-05-24 06:52:49 UTC
Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-24 08:01:08 UTC
Re: linear bearing based on ground flat stock
wthomas@g...
2006-05-24 10:48:02 UTC
W.E.T. [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock
Graham Stabler
2006-05-24 15:52:20 UTC
W.E.T. [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock