CAD CAM EDM DRO - Yahoo Group Archive

Re: linear bearing based on ground flat stock

Posted by ballendo
on 2006-05-22 20:04:04 UTC
Bill,

You are exactly correct.

It would even be possible to turn the square into a flat with vee
edges. (put it in a couple of vee blocks on a mill and go to town!<G>

It could be mounted horizontally or vertically.

I guess I was thinking of a 1" square bar and two skate bearing
thicknesses being abou .550, with a need for a bit between them. Had
the face of the bar "covered".

Thank you for pointing out there is NO downside!<G>

Ballendo

--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@... wrote:
>
>
> In a message dated 5/22/2006 4:11:32 P.M. Mountain Daylight Time,
> ballendo@... writes:
>
> Down side is the need to end mount the bar. But at your light
loads
> and relatively small travels this shouldn't be a deal-breaker.
>
>
>
> Why can't the bar be multi position mounted as long as your mounts
can clear
> the V Pulleys on two opposite sides.
> Won't the 2 V pulleys on opposite sides bear on surfaces in all
four
> directions, left right, up, down???
> In fact, as far as the bar is concerned, each direction has two
alignment
> surfaces from the V of the pulleys.
>
> If you set the edges of the bar vertical, they could be mounted
all along
> one horizontal side with a narrow web type of mount.
> IMHO
> bill
>
>
> [Non-text portions of this message have been removed]
>

Discussion Thread

Graham Stabler 2006-05-21 13:11:26 UTC linear bearing based on ground flat stock Jack Hudler 2006-05-21 15:42:03 UTC RE: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock Graham Stabler 2006-05-21 17:40:00 UTC Re: linear bearing based on ground flat stock Aftiel 2006-05-21 18:56:59 UTC Re: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock Jack Hudler 2006-05-21 19:53:32 UTC RE: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock Jack Hudler 2006-05-21 20:23:45 UTC RE: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock JanRwl@A... 2006-05-21 23:20:43 UTC Re: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock ballendo 2006-05-22 02:10:28 UTC Re: linear bearing based on ground flat stock Les Newell 2006-05-22 02:28:57 UTC Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock ballendo 2006-05-22 02:38:27 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-22 03:24:39 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-22 03:27:07 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-22 03:37:54 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 04:07:14 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 04:12:34 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 04:19:13 UTC Re: linear bearing based on ground flat stock tomp-tag 2006-05-22 06:27:51 UTC Re: linear bearing based on ground flat stock Jack Hudler 2006-05-22 11:03:57 UTC RE: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock wanliker@a... 2006-05-22 11:07:17 UTC Re: [CAD_CAM_EDM_DRO] linear bearing based on ground flat stock Graham Stabler 2006-05-22 12:12:12 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-22 12:19:12 UTC Re: linear bearing based on ground flat stock wanliker@a... 2006-05-22 12:30:13 UTC Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock wanliker@a... 2006-05-22 12:37:49 UTC Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock Graham Stabler 2006-05-22 12:59:33 UTC Re: linear bearing based on ground flat stock wanliker@a... 2006-05-22 13:20:59 UTC Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock ballendo 2006-05-22 14:49:37 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 15:10:31 UTC Re: linear bearing based on ground flat stock wanliker@a... 2006-05-22 15:33:21 UTC linear bearing based on ground flat stock Jack Hudler 2006-05-22 15:39:38 UTC RE: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock turbulatordude 2006-05-22 17:57:06 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-22 18:07:59 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-22 18:09:55 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 20:04:04 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 20:06:24 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 20:12:47 UTC Re: linear bearing based on ground flat stock turbulatordude 2006-05-22 20:52:13 UTC Re: linear bearing based on ground flat stock JanRwl@A... 2006-05-22 22:00:30 UTC Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock wanliker@a... 2006-05-22 22:17:59 UTC linear bearing based on ground flat stock ballendo 2006-05-22 22:35:03 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-22 22:44:35 UTC Re: linear bearing based on ground flat stock wthomas@g... 2006-05-22 23:25:58 UTC W.E.T. [CAD_CAM_EDM_DRO] Rd bearing based on ground Drill Rod Graham Stabler 2006-05-23 03:23:00 UTC Re: linear bearing based on ground flat stock Fred Smith 2006-05-23 07:10:50 UTC Re: linear bearing based on ground flat stock turbulatordude 2006-05-23 09:08:10 UTC Re: linear bearing based on ground flat stock Fred Smith 2006-05-23 09:28:44 UTC Re: linear bearing based on ground flat stock turbulatordude 2006-05-23 10:37:42 UTC Re: linear bearing based on ground flat stock ballendo 2006-05-23 14:43:24 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-23 16:09:18 UTC Re: linear bearing based on ground flat stock Blue 2006-05-23 18:06:42 UTC Re: [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock Graham Stabler 2006-05-24 02:50:27 UTC Re: linear bearing based on ground flat stock turbulatordude 2006-05-24 06:52:49 UTC Re: linear bearing based on ground flat stock Graham Stabler 2006-05-24 08:01:08 UTC Re: linear bearing based on ground flat stock wthomas@g... 2006-05-24 10:48:02 UTC W.E.T. [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock Graham Stabler 2006-05-24 15:52:20 UTC W.E.T. [CAD_CAM_EDM_DRO] Re: linear bearing based on ground flat stock