Re: [CAD_CAM_EDM_DRO] Re: Power supply
Posted by
Abby Katt
on 2006-05-30 04:36:35 UTC
Hi there,
One potential problem here... you may be able to connect two linear
power supplies (or batteries even) in series to double the voltage, but
when you do that with a switched mode power supply (i.e.computer PSU)...
*BANG*. Switch mode PSU's monitor the output stage in a type of complex
"loop" so they can't be chained to double the voltage, even putting them
in series is likely to be asking for serious trouble...
If you need 24V it's best to just get a cheap PSU that does 24V, or even
build your own.
Otherwise you're at 12V, but your performance for steppers rated 24V at
12V is going to be abyssmal. You'd be better off with 2-3V steppers and
a chopper drive (Xylotex/Gecko and friends)...
Regards,
Abby
One potential problem here... you may be able to connect two linear
power supplies (or batteries even) in series to double the voltage, but
when you do that with a switched mode power supply (i.e.computer PSU)...
*BANG*. Switch mode PSU's monitor the output stage in a type of complex
"loop" so they can't be chained to double the voltage, even putting them
in series is likely to be asking for serious trouble...
If you need 24V it's best to just get a cheap PSU that does 24V, or even
build your own.
Otherwise you're at 12V, but your performance for steppers rated 24V at
12V is going to be abyssmal. You'd be better off with 2-3V steppers and
a chopper drive (Xylotex/Gecko and friends)...
Regards,
Abby
>My machine isn't going to be that big. At the largest it would have a[Non-text portions of this message have been removed]
>cutting area of 12"X12"x3" . I'd think that the 12v, or 24+ of I
>connected a few together would be more than enough. The steppers I
>have are only 24v.
>
>
>--- In CAD_CAM_EDM_DRO@yahoogroups.com, "caudlet" <thom@...> wrote:
>
>
>>--- In CAD_CAM_EDM_DRO@yahoogroups.com, "krashking405"
>><krashking405@> wrote:
>>
>>
>>>I'm planning on using 1 or 2 computer PSUs to power my setup.
>>>
>>>
>Planning
>
>
>>>on using 1 just for the controllers, and 1 for the steppers. Any
>>>suggestions?
>>>
>>>
>>>
>> Your machine will perform poorly and your rapids will be slow. You
>>will need to learn to be patient. The highest voltage on a computer
>>power supply is typically 12VDC.
>>
>>
>>
>
>
>
>
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
Discussion Thread
pkranger63@y...
2001-11-23 18:04:55 UTC
Power supply
Bob Campbell
2001-11-23 18:20:33 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
shymu@b...
2001-11-23 18:52:44 UTC
Re: Power supply
shymu@b...
2001-11-23 19:31:37 UTC
Re: Power supply
Bill Vance
2001-11-23 22:58:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
High Tech
2001-11-24 08:52:14 UTC
RE: [CAD_CAM_EDM_DRO] Power supply
Bill Vance
2002-04-19 11:42:57 UTC
Power supply
mariss92705
2002-04-19 12:31:28 UTC
Re: Power supply
workaholic_ro
2002-04-19 14:48:59 UTC
Re: Power supply
mariss92705
2002-04-19 19:42:33 UTC
Re: Power supply
Raymond Heckert
2002-06-23 13:34:15 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
JanRwl@A...
2002-06-23 15:57:22 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
krashking405
2006-05-28 16:26:37 UTC
Power supply
caudlet
2006-05-29 08:12:33 UTC
Re: Power supply
krashking405
2006-05-29 16:42:34 UTC
Re: Power supply
Abby Katt
2006-05-30 04:36:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
ballendo
2006-05-30 05:40:35 UTC
Re: Power supply
Graham Stabler
2006-05-30 07:25:37 UTC
Re: Power supply
Roy J. Tellason
2006-05-30 08:09:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Roy J. Tellason
2006-05-30 08:16:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Mina Aboul Saad
2006-06-24 04:11:52 UTC
Power supply
Lester Caine
2006-06-24 04:48:07 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
Abby Katt
2006-06-24 05:02:00 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
Peter Reilley
2006-06-24 05:22:03 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
Larry Bush
2006-06-24 05:32:54 UTC
Re: Power supply
Tony Jeffree
2006-06-24 05:49:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
David Speck
2006-06-24 06:40:16 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
Robert Renfro
2006-06-24 07:26:09 UTC
Re: Power supply
Robert Campbell
2006-06-24 07:26:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Thea xxxxx
2006-06-24 07:26:56 UTC
AW: [CAD_CAM_EDM_DRO] Power supply
David Speck
2006-06-24 07:37:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Peter Reilley
2006-06-24 07:58:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
David Speck
2006-06-24 08:47:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Peter Reilley
2006-06-24 09:38:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Stephen Wille Padnos
2006-06-24 09:47:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
turbulatordude
2006-06-24 10:28:46 UTC
Re: Power supply
Peter Reilley
2006-06-24 11:12:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
David Speck
2006-06-24 12:34:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Peter Reilley
2006-06-24 13:44:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply
Dave Halliday
2006-06-24 18:59:21 UTC
RE: [CAD_CAM_EDM_DRO] Power supply
Raymond Heckert
2006-06-25 18:12:16 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
Jon Elson
2006-06-25 22:19:08 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
Jack Mc Kie
2008-06-11 07:58:00 UTC
Power supply
JCullins
2008-06-11 10:22:56 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
Jon Elson
2008-06-11 10:25:31 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
David G. LeVine
2008-06-13 09:39:29 UTC
Re: [CAD_CAM_EDM_DRO] Power supply
caudlet
2008-06-13 11:03:45 UTC
Re: Power supply