Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
Posted by
Mike Gann
on 2001-05-19 14:54:04 UTC
Wow - and I thought the pulleys could start to add up!!
$25 for the smallest and the price just goes up from there.
Mike
ptengin@... wrote:
$25 for the smallest and the price just goes up from there.
Mike
ptengin@... wrote:
> Chris,
>
> Have played with those Fenner units too. They are very high dollar and
> work really well. If they are installed per spec, they should transmit any
> load the shaft is rated to carry. Since there is no keyway, I'd think that
> fatigue cracking is easier to avoid. The shafting need not be ground but it
> must be a good finish. Also, I think the diameter could be +- .001 in less
> critical applications. Sure beats cutting keyways.
>
> Peter
> THRD, Inc.
>
> [Non-text portions of this message have been removed]
>
>
Discussion Thread
Mike Gann
2001-05-18 19:09:41 UTC
Souces of Timing/Drive Pulleys
Tim Goldstein
2001-05-18 19:24:21 UTC
RE: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys
Hugh & Denise Currin
2001-05-18 21:46:43 UTC
Re: Souces of Timing/Drive Pulleys
Mike Gann
2001-05-18 22:17:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
Jon Elson
2001-05-18 22:28:16 UTC
Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys
Mike Gann
2001-05-18 22:33:21 UTC
Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys
machines@n...
2001-05-18 23:45:38 UTC
Re: Souces of Timing/Drive Pulleys
Les Watts
2001-05-19 03:01:29 UTC
Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys
phrh@w...
2001-05-19 04:40:40 UTC
Re: Souces of Timing/Drive Pulleys
A. G. Eckstein
2001-05-19 05:00:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
Chris Stratton
2001-05-19 07:25:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
Jerry Kimberlin
2001-05-19 07:58:14 UTC
Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys
Ray
2001-05-19 10:12:35 UTC
Re: Re: Souces of Timing/Drive Pulleys
Chris Stratton
2001-05-19 10:15:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Souces of Timing/Drive Pulleys
ptengin@a...
2001-05-19 12:45:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
Mike Gann
2001-05-19 14:54:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
machines@n...
2001-05-19 15:27:28 UTC
Re: Souces of Timing/Drive Pulleys
Hugh Currin
2001-05-20 17:20:50 UTC
Re: Souces of Timing/Drive Pulleys
Hugh Currin
2001-05-20 17:28:34 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-21 20:06:18 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-21 20:20:29 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-21 20:35:25 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-21 21:04:18 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-21 21:14:07 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-21 21:45:07 UTC
Re: Souces of Timing/Drive Pulleys
Carey L. Culpepper
2001-05-22 08:04:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
Jon Elson
2001-05-22 14:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
dave engvall
2001-05-22 19:29:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
machines@n...
2001-05-23 00:49:23 UTC
Re: Souces of Timing/Drive Pulleys
Hugh Currin
2001-05-23 09:59:10 UTC
Re: Souces of Timing/Drive Pulleys
ptengin@a...
2001-05-23 13:03:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
machines@n...
2001-05-23 15:05:00 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-24 16:21:21 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-24 18:01:56 UTC
Re: Souces of Timing/Drive Pulleys
Carey L. Culpepper
2001-05-24 18:20:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-24 19:51:04 UTC
Re: Souces of Timing/Drive Pulleys
ballendo@y...
2001-05-24 20:22:07 UTC
Re: Souces of Timing/Drive Pulleys
machines@n...
2001-05-25 00:35:47 UTC
Re: Souces of Timing/Drive Pulleys
Smoke
2001-05-28 10:21:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys