CAD CAM EDM DRO - Yahoo Group Archive

Re: Souces of Timing/Drive Pulleys

Posted by ballendo@y...
on 2001-05-21 20:06:18 UTC
Hello,
Boston bearing or York are good sources,IMO. Once again, I'll suggest
STRONGLY using the htd (parabolic)tooth form, rather than xl
(trapezoid)! One case where the new technology IS better! Vastly so...

Hope this helps.

Ballendo

Mike wrote:

> >What have all you guys been using as a source for your
> >timing pulleys'?
<snip>

Discussion Thread

Mike Gann 2001-05-18 19:09:41 UTC Souces of Timing/Drive Pulleys Tim Goldstein 2001-05-18 19:24:21 UTC RE: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys Hugh & Denise Currin 2001-05-18 21:46:43 UTC Re: Souces of Timing/Drive Pulleys Mike Gann 2001-05-18 22:17:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Jon Elson 2001-05-18 22:28:16 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys Mike Gann 2001-05-18 22:33:21 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys machines@n... 2001-05-18 23:45:38 UTC Re: Souces of Timing/Drive Pulleys Les Watts 2001-05-19 03:01:29 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys phrh@w... 2001-05-19 04:40:40 UTC Re: Souces of Timing/Drive Pulleys A. G. Eckstein 2001-05-19 05:00:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Chris Stratton 2001-05-19 07:25:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Jerry Kimberlin 2001-05-19 07:58:14 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys Ray 2001-05-19 10:12:35 UTC Re: Re: Souces of Timing/Drive Pulleys Chris Stratton 2001-05-19 10:15:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Souces of Timing/Drive Pulleys ptengin@a... 2001-05-19 12:45:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Mike Gann 2001-05-19 14:54:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-19 15:27:28 UTC Re: Souces of Timing/Drive Pulleys Hugh Currin 2001-05-20 17:20:50 UTC Re: Souces of Timing/Drive Pulleys Hugh Currin 2001-05-20 17:28:34 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 20:06:18 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 20:20:29 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 20:35:25 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 21:04:18 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 21:14:07 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 21:45:07 UTC Re: Souces of Timing/Drive Pulleys Carey L. Culpepper 2001-05-22 08:04:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Jon Elson 2001-05-22 14:20:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys dave engvall 2001-05-22 19:29:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-23 00:49:23 UTC Re: Souces of Timing/Drive Pulleys Hugh Currin 2001-05-23 09:59:10 UTC Re: Souces of Timing/Drive Pulleys ptengin@a... 2001-05-23 13:03:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-23 15:05:00 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 16:21:21 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 18:01:56 UTC Re: Souces of Timing/Drive Pulleys Carey L. Culpepper 2001-05-24 18:20:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 19:51:04 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 20:22:07 UTC Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-25 00:35:47 UTC Re: Souces of Timing/Drive Pulleys Smoke 2001-05-28 10:21:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys