CAD CAM EDM DRO - Yahoo Group Archive

Re: Souces of Timing/Drive Pulleys

Posted by ballendo@y...
on 2001-05-21 20:35:25 UTC
Chris,

Taper lock hubs out perform keyways and pins, and are tolerant of
shaft size variations as well...

Hope this helps.

Ballendo

--- In CAD_CAM_EDM_DRO@y..., Chris Stratton <stratton@m...> wrote:
> > Why don't you want to bore out the hubs? My plan is to do this,
bore the
> > pulleys, and use a taper lock hub to avoid a keyway. (Also avoid
coming up
> > with a broach set.) These are Fenner taper lock hubs (from MSC)
rather
> > than the integral taper locks built into some pulleys.
>
> I'm not familiar with these hubs, but would think that they would
> require a very precisely machined (ground?) shaft (okay, I know,
we're
> _supposed_ to do that for the bearings anyway) and even then they
> might still slip under high cutting or acceleration loads. If your
> encoder is upstream of the pulley system, wouldn't some sort of pin
be
> safer?
>
> Chris

Discussion Thread

Mike Gann 2001-05-18 19:09:41 UTC Souces of Timing/Drive Pulleys Tim Goldstein 2001-05-18 19:24:21 UTC RE: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys Hugh & Denise Currin 2001-05-18 21:46:43 UTC Re: Souces of Timing/Drive Pulleys Mike Gann 2001-05-18 22:17:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Jon Elson 2001-05-18 22:28:16 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys Mike Gann 2001-05-18 22:33:21 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys machines@n... 2001-05-18 23:45:38 UTC Re: Souces of Timing/Drive Pulleys Les Watts 2001-05-19 03:01:29 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys phrh@w... 2001-05-19 04:40:40 UTC Re: Souces of Timing/Drive Pulleys A. G. Eckstein 2001-05-19 05:00:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Chris Stratton 2001-05-19 07:25:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Jerry Kimberlin 2001-05-19 07:58:14 UTC Re: [CAD_CAM_EDM_DRO] Souces of Timing/Drive Pulleys Ray 2001-05-19 10:12:35 UTC Re: Re: Souces of Timing/Drive Pulleys Chris Stratton 2001-05-19 10:15:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Souces of Timing/Drive Pulleys ptengin@a... 2001-05-19 12:45:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Mike Gann 2001-05-19 14:54:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-19 15:27:28 UTC Re: Souces of Timing/Drive Pulleys Hugh Currin 2001-05-20 17:20:50 UTC Re: Souces of Timing/Drive Pulleys Hugh Currin 2001-05-20 17:28:34 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 20:06:18 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 20:20:29 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 20:35:25 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 21:04:18 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 21:14:07 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-21 21:45:07 UTC Re: Souces of Timing/Drive Pulleys Carey L. Culpepper 2001-05-22 08:04:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys Jon Elson 2001-05-22 14:20:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys dave engvall 2001-05-22 19:29:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-23 00:49:23 UTC Re: Souces of Timing/Drive Pulleys Hugh Currin 2001-05-23 09:59:10 UTC Re: Souces of Timing/Drive Pulleys ptengin@a... 2001-05-23 13:03:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-23 15:05:00 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 16:21:21 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 18:01:56 UTC Re: Souces of Timing/Drive Pulleys Carey L. Culpepper 2001-05-24 18:20:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 19:51:04 UTC Re: Souces of Timing/Drive Pulleys ballendo@y... 2001-05-24 20:22:07 UTC Re: Souces of Timing/Drive Pulleys machines@n... 2001-05-25 00:35:47 UTC Re: Souces of Timing/Drive Pulleys Smoke 2001-05-28 10:21:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Souces of Timing/Drive Pulleys