Re: [CAD_CAM_EDM_DRO] Black box again
Posted by
Jon Elson
on 2001-06-26 19:44:38 UTC
Tom Eldredge wrote:
I had real problems figuring out the partitions so that it would
install on less than 1 GB. Unless this would be a CNC only
system, with no software development done on the machine,
and you have another machine to compile EMC on, I would
suggest 1 GB minimum.
You'll also get to see my (horrible) shop. (Horrible because
of all the stuff piled everywhere!)
Jon
> Thanks, Jon,I've got it on a 1 GB SCSI disk. An IDE should be fine, too.
>
> That is quite an offer, and I think I'll take you up on it.
>
> What would be the minimum drive requirements be?
I had real problems figuring out the partitions so that it would
install on less than 1 GB. Unless this would be a CNC only
system, with no software development done on the machine,
and you have another machine to compile EMC on, I would
suggest 1 GB minimum.
You'll also get to see my (horrible) shop. (Horrible because
of all the stuff piled everywhere!)
Jon
Discussion Thread
Tom Eldredge
2001-06-25 09:45:32 UTC
Black box again
William Scalione
2001-06-25 11:05:56 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Dennis Cranston
2001-06-25 11:07:06 UTC
RE: [CAD_CAM_EDM_DRO] Black box again
Jon Elson
2001-06-25 11:21:18 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Tim Goldstein
2001-06-25 11:37:10 UTC
RE: [CAD_CAM_EDM_DRO] Black box again
Peter Renolds
2001-06-25 11:55:01 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Tom Eldredge
2001-06-25 12:12:32 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Tim Goldstein
2001-06-25 12:22:19 UTC
RE: [CAD_CAM_EDM_DRO] Black box again
Chris Stratton
2001-06-25 12:28:10 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Alan Marconett KM6VV
2001-06-25 13:30:31 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
joelulaw@y...
2001-06-25 13:48:13 UTC
Re: Black box again
Jon Elson
2001-06-25 17:14:50 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Jon Elson
2001-06-25 17:19:42 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Jon Elson
2001-06-25 17:22:04 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Jon Elson
2001-06-25 20:03:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
machines@n...
2001-06-25 22:51:50 UTC
Re: Black box again
machines@n...
2001-06-25 22:56:31 UTC
Re: Black box again
Tom Eldredge
2001-06-26 04:19:47 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
ballendo@y...
2001-06-26 06:07:01 UTC
Re: Black box again
Tom Eldredge
2001-06-26 06:34:16 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
joelulaw@y...
2001-06-26 07:21:34 UTC
Re: Black box again
Tom Eldredge
2001-06-26 07:38:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Jon Elson
2001-06-26 10:59:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Jon Elson
2001-06-26 11:04:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Jon Elson
2001-06-26 11:14:35 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Alan Marconett KM6VV
2001-06-26 11:33:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Tom Eldredge
2001-06-26 12:34:13 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Ian Wright
2001-06-26 12:38:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Carol & Jerry Jankura
2001-06-26 14:51:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Black box again
Jon Elson
2001-06-26 19:40:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Jon Elson
2001-06-26 19:44:38 UTC
Re: [CAD_CAM_EDM_DRO] Black box again
Alan Marconett KM6VV
2001-06-26 21:57:42 UTC
Re: Black box again
dkowalcz@i...
2001-06-26 23:15:13 UTC
Re: Black box again
Jon Elson
2001-06-26 23:49:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Alan Marconett KM6VV
2001-06-27 11:06:46 UTC
Re: Black box again
Tom Eldredge
2001-06-27 11:31:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
JanRwl@A...
2001-06-27 11:35:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Tom Eldredge
2001-06-27 11:38:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Alan Marconett KM6VV
2001-06-27 12:54:34 UTC
Re: Black box again
Alan Marconett KM6VV
2001-06-27 13:05:07 UTC
Re: Black box again
ballendo@y...
2001-06-27 16:00:20 UTC
Re: Black box again
ballendo@y...
2001-06-27 16:52:28 UTC
fire and forget was Re: Black box again
Alan Marconett KM6VV
2001-06-27 18:12:32 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
ballendo@y...
2001-06-27 18:45:13 UTC
re:fire and forget was Re: Black box again
Alan Marconett KM6VV
2001-06-27 19:30:30 UTC
re:fire and forget was Re: Black box again
Jon Elson
2001-06-27 20:27:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Eric Keller
2001-06-27 20:28:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Jon Elson
2001-06-27 20:31:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Jon Elson
2001-06-27 20:53:49 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
Alan Marconett KM6VV
2001-06-27 23:49:53 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
Tom Eldredge
2001-06-28 04:05:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
dkowalcz@i...
2001-06-28 06:41:01 UTC
Re: Black box again
ballendo@y...
2001-06-28 07:53:00 UTC
Re: Black box again
ballendo@y...
2001-06-28 07:59:53 UTC
Re: Black box again
Jon Elson
2001-06-28 10:54:26 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
Alan Marconett KM6VV
2001-06-28 11:39:16 UTC
Re: Black box again
Art Fenerty
2001-06-28 11:41:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again
Alan Marconett KM6VV
2001-06-28 12:31:35 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
Paul
2001-06-28 15:29:11 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
Jon Elson
2001-06-28 20:12:48 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
Jon Elson
2001-06-28 20:19:49 UTC
Re: [CAD_CAM_EDM_DRO] fire and forget was Re: Black box again
Tom Eldredge
2001-06-29 04:14:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Black box again