CAD CAM EDM DRO - Yahoo Group Archive

Re: Here's my proposed power supply setup.

on 2002-08-17 06:31:37 UTC
Lloyd,

There are some of us that use a DC powered fan (www.jameco.com) on
the DC bus. draws less than 0.1 amp, makes noise, and bleads your
cap at the same time. The noise is an added bonus when you open the
case.

And for another blead loop, check Mariss's power supply loop in the
files section. drops the power of the cap shortly after the power
goes off. Only caveat is that ( I think it was Les) mentioned
brownouts may activate the circuit. Quick search for the posts will
reveal that discussion.

Dave





--- In CAD_CAM_EDM_DRO@y..., "Lloyd Leung" <lloyd@l...> wrote:
> Thanks for the corrections Mariss, it's much appreciated. I now
> understand the major parts of this power supply.
>
> However, there are still a few questions I have...
>
> I purchased is a switch that breaks the connection for both AC wires
> (switches on/off for both wires from the AC in), is this a good
idea? I
> know that the capacitor will act like a battery if I use this kind
of
> switch, as the power will have no were to go. To alleviate this
> potential shock hazard, I will put a bleeder resistor on it. I
> currently have two bleeder resisters - 620ohm 10W, and a 500ohm 5W.
> Which one should I use or does it matter, or should I go out and get
> something else?
>
> If this is a bad idea... how should I implement a switch to power
on/off
> my power supply?
>
>
> Also, what type of computer CPU Fan was good to use with the Geckos?
>
>
>
> Thanks.
>
> Lloyd
>
<snip>

Discussion Thread

Lloyd Leung 2002-08-15 21:03:45 UTC Here's my proposed power supply setup. mariss92705 2002-08-16 01:13:19 UTC Re: Here's my proposed power supply setup. rawen2 2002-08-16 09:43:38 UTC Q for Mariss (was Re: Here's my proposed power supply setup.) mayfieldtm 2002-08-16 09:45:38 UTC Re: Here's my proposed power supply setup. JJ 2002-08-16 12:58:43 UTC RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup. JJ 2002-08-16 13:02:50 UTC RE: [CAD_CAM_EDM_DRO] Q for Mariss (was Re: Here's my proposed power supply setup.) mayfieldtm 2002-08-16 14:53:34 UTC Re: Here's my proposed power supply setup. turbulatordude 2002-08-16 15:37:50 UTC Q for Mariss (was Re: Here's my proposed power supply setup.) mariss92705 2002-08-16 18:32:01 UTC Re: Here's my proposed power supply setup. mariss92705 2002-08-16 18:42:42 UTC Q for Mariss (was Re: Here's my proposed power supply setup.) Jon Elson 2002-08-16 21:35:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup. Lloyd Leung 2002-08-16 22:05:01 UTC RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup. andrewyslee 2002-08-16 22:30:11 UTC quickie LED lesson Lloyd Leung 2002-08-16 22:36:13 UTC RE: [CAD_CAM_EDM_DRO] quickie LED lesson turbulatordude 2002-08-17 06:31:37 UTC Re: Here's my proposed power supply setup. Les Watts 2002-08-17 07:25:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup. JJ 2002-08-17 09:36:42 UTC RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup. mariss92705 2002-08-17 11:56:07 UTC Re: Here's my proposed power supply setup. mariss92705 2002-08-17 12:01:00 UTC Re: Here's my proposed power supply setup. Mike 2002-08-17 12:51:50 UTC RE: [CAD_CAM_EDM_DRO] quickie LED lesson pcfw 2002-08-17 12:51:50 UTC Re: quickie LED lesson Brian 2002-08-17 13:41:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup. mayfieldtm 2002-08-17 13:59:01 UTC Shock Warning JJ 2002-08-17 14:32:15 UTC RE: [CAD_CAM_EDM_DRO] Shock Warning Matt Shaver 2002-08-17 19:31:26 UTC Re: [CAD_CAM_EDM_DRO] Shock Warning JanRwl@A... 2002-08-17 20:03:43 UTC Re: [CAD_CAM_EDM_DRO] quickie LED lesson turbulatordude 2002-08-17 20:30:15 UTC Re: Shock Warning Keith Green 2002-08-17 20:51:02 UTC Re: [CAD_CAM_EDM_DRO] Shock Warning mayfieldtm 2002-08-18 00:19:02 UTC Re: Shock Warning stevenson_engineers 2002-08-18 01:43:55 UTC Re: Shock Warning mariss92705 2002-08-18 04:10:55 UTC Re: Shock Warning stevenson_engineers 2002-08-18 04:30:11 UTC Re: Shock Warning bjammin@i... 2002-08-18 04:35:56 UTC Re: [CAD_CAM_EDM_DRO] Shock Warning bjammin@i... 2002-08-18 04:36:07 UTC waaaay OT JJ 2002-08-18 05:33:10 UTC RE: [CAD_CAM_EDM_DRO] Shock Warning turbulatordude 2002-08-18 06:21:07 UTC Re: waaaay OT Mike 2002-08-18 06:33:12 UTC RE: [CAD_CAM_EDM_DRO] quickie LED lesson mayfieldtm 2002-08-18 09:08:05 UTC Re: quickie LED lesson Ian W. Wright 2002-08-18 09:38:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Shock Warning Clinton Driggars 2002-08-18 11:48:56 UTC Re: [CAD_CAM_EDM_DRO] Re: Shock Warning wanliker@a... 2002-08-18 12:06:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Shock Warning JanRwl@A... 2002-08-18 13:39:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Shock Warning JanRwl@A... 2002-08-18 14:00:00 UTC Re: [CAD_CAM_EDM_DRO] Re: waaaay OT JanRwl@A... 2002-08-18 14:04:06 UTC Re: [CAD_CAM_EDM_DRO] quickie LED lesson George Wealleans 2002-08-18 15:20:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Shock Warning wanliker@a... 2002-08-18 16:59:59 UTC Re: [CAD_CAM_EDM_DRO] Re: waaaay OT cncnovice 2002-08-18 17:28:01 UTC Re: Shock Warning Keith Green 2002-08-18 17:41:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Shock Warning Zoran A. Scepanovic 2002-08-19 01:24:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Shock Warning bjammin@i... 2002-08-19 02:56:12 UTC waaaay waaaaay beyond OT caudlet 2002-08-19 05:35:14 UTC Re: Shock Warning