Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
Posted by
Les Watts
on 2002-08-17 07:25:47 UTC
Mariss' circuit will track a brownout. It tracks the xformer secondary.
So it should not activate with either high or low mains voltage.(I think)
It will activate when the cap is some voltage above the secondary peak
voltage.I just got in 50,000 uf and about 50 lb of transformer for a new
servo supply for my machine. I have been running at reduced acel
due to a small supply. I will use Mariss' circuit in this.
Les
Leslie Watts
L M Watts Furniture
Tiger, Georgia USA
http://www.alltel.net/~leswatts/wattsfurniturewp.html
engineering page:
http://www.alltel.net/~leswatts/shop.html
So it should not activate with either high or low mains voltage.(I think)
It will activate when the cap is some voltage above the secondary peak
voltage.I just got in 50,000 uf and about 50 lb of transformer for a new
servo supply for my machine. I have been running at reduced acel
due to a small supply. I will use Mariss' circuit in this.
Les
Leslie Watts
L M Watts Furniture
Tiger, Georgia USA
http://www.alltel.net/~leswatts/wattsfurniturewp.html
engineering page:
http://www.alltel.net/~leswatts/shop.html
----- Original Message -----
From: "turbulatordude" <davemucha@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, August 17, 2002 9:31 AM
Subject: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
> Lloyd,
>
> There are some of us that use a DC powered fan (www.jameco.com) on
> the DC bus. draws less than 0.1 amp, makes noise, and bleads your
> cap at the same time. The noise is an added bonus when you open the
> case.
>
> And for another blead loop, check Mariss's power supply loop in the
> files section. drops the power of the cap shortly after the power
> goes off. Only caveat is that ( I think it was Les) mentioned
> brownouts may activate the circuit. Quick search for the posts will
> reveal that discussion.
>
> Dave
>
Discussion Thread
Lloyd Leung
2002-08-15 21:03:45 UTC
Here's my proposed power supply setup.
mariss92705
2002-08-16 01:13:19 UTC
Re: Here's my proposed power supply setup.
rawen2
2002-08-16 09:43:38 UTC
Q for Mariss (was Re: Here's my proposed power supply setup.)
mayfieldtm
2002-08-16 09:45:38 UTC
Re: Here's my proposed power supply setup.
JJ
2002-08-16 12:58:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
JJ
2002-08-16 13:02:50 UTC
RE: [CAD_CAM_EDM_DRO] Q for Mariss (was Re: Here's my proposed power supply setup.)
mayfieldtm
2002-08-16 14:53:34 UTC
Re: Here's my proposed power supply setup.
turbulatordude
2002-08-16 15:37:50 UTC
Q for Mariss (was Re: Here's my proposed power supply setup.)
mariss92705
2002-08-16 18:32:01 UTC
Re: Here's my proposed power supply setup.
mariss92705
2002-08-16 18:42:42 UTC
Q for Mariss (was Re: Here's my proposed power supply setup.)
Jon Elson
2002-08-16 21:35:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
Lloyd Leung
2002-08-16 22:05:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
andrewyslee
2002-08-16 22:30:11 UTC
quickie LED lesson
Lloyd Leung
2002-08-16 22:36:13 UTC
RE: [CAD_CAM_EDM_DRO] quickie LED lesson
turbulatordude
2002-08-17 06:31:37 UTC
Re: Here's my proposed power supply setup.
Les Watts
2002-08-17 07:25:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
JJ
2002-08-17 09:36:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
mariss92705
2002-08-17 11:56:07 UTC
Re: Here's my proposed power supply setup.
mariss92705
2002-08-17 12:01:00 UTC
Re: Here's my proposed power supply setup.
Mike
2002-08-17 12:51:50 UTC
RE: [CAD_CAM_EDM_DRO] quickie LED lesson
pcfw
2002-08-17 12:51:50 UTC
Re: quickie LED lesson
Brian
2002-08-17 13:41:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
mayfieldtm
2002-08-17 13:59:01 UTC
Shock Warning
JJ
2002-08-17 14:32:15 UTC
RE: [CAD_CAM_EDM_DRO] Shock Warning
Matt Shaver
2002-08-17 19:31:26 UTC
Re: [CAD_CAM_EDM_DRO] Shock Warning
JanRwl@A...
2002-08-17 20:03:43 UTC
Re: [CAD_CAM_EDM_DRO] quickie LED lesson
turbulatordude
2002-08-17 20:30:15 UTC
Re: Shock Warning
Keith Green
2002-08-17 20:51:02 UTC
Re: [CAD_CAM_EDM_DRO] Shock Warning
mayfieldtm
2002-08-18 00:19:02 UTC
Re: Shock Warning
stevenson_engineers
2002-08-18 01:43:55 UTC
Re: Shock Warning
mariss92705
2002-08-18 04:10:55 UTC
Re: Shock Warning
stevenson_engineers
2002-08-18 04:30:11 UTC
Re: Shock Warning
bjammin@i...
2002-08-18 04:35:56 UTC
Re: [CAD_CAM_EDM_DRO] Shock Warning
bjammin@i...
2002-08-18 04:36:07 UTC
waaaay OT
JJ
2002-08-18 05:33:10 UTC
RE: [CAD_CAM_EDM_DRO] Shock Warning
turbulatordude
2002-08-18 06:21:07 UTC
Re: waaaay OT
Mike
2002-08-18 06:33:12 UTC
RE: [CAD_CAM_EDM_DRO] quickie LED lesson
mayfieldtm
2002-08-18 09:08:05 UTC
Re: quickie LED lesson
Ian W. Wright
2002-08-18 09:38:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
Clinton Driggars
2002-08-18 11:48:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
wanliker@a...
2002-08-18 12:06:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
JanRwl@A...
2002-08-18 13:39:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
JanRwl@A...
2002-08-18 14:00:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: waaaay OT
JanRwl@A...
2002-08-18 14:04:06 UTC
Re: [CAD_CAM_EDM_DRO] quickie LED lesson
George Wealleans
2002-08-18 15:20:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
wanliker@a...
2002-08-18 16:59:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: waaaay OT
cncnovice
2002-08-18 17:28:01 UTC
Re: Shock Warning
Keith Green
2002-08-18 17:41:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
Zoran A. Scepanovic
2002-08-19 01:24:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
bjammin@i...
2002-08-19 02:56:12 UTC
waaaay waaaaay beyond OT
caudlet
2002-08-19 05:35:14 UTC
Re: Shock Warning