Re: Shock Warning
Posted by
stevenson_engineers
on 2002-08-18 04:30:11 UTC
Thank you Marris,
At last a sensible reply to something we all know if we care to admit
it.
I'm sure many here have had a shock of some type and greater than the
stated currents.
If so are all the posts posthumerious ???
John S.
At last a sensible reply to something we all know if we care to admit
it.
I'm sure many here have had a shock of some type and greater than the
stated currents.
If so are all the posts posthumerious ???
John S.
>--- In CAD_CAM_EDM_DRO@y..., "mariss92705" <mariss92705@y...> wrote:your
> Take an ohmmeter. Squeeze The terminals as hard as you can. Lick
> fingers to make the reading as low as possible. I don't think youlet
> will get under 2,000 Ohms.
>
> It takes about 100mA to get you to be in trouble, i.e. you can't
> go of the leads. Do Ohms Law to figure the voltage needed to getyour
> 100mA to go thru you when you have 2K of resistance. That works out
> to be 200 volts.
>
> 9VDC does indeed tickle when you touch your tongue to it but it is
> not hazardous, let alone lethal. It takes 100mA at least to get
> yourself in trouble, and then it must pass thru your heart. To do
> that it must go up one arm, thru your chest and down the other arm.
>
> All good techincians and engineers know when you are dealing with
> potentially leathal voltages to keep one arm behind your back. The
> other one you can stick into dangerous parts. If you are wrong,
> fingers will get burned but current won't pass thru your chest and1A
> arrest your heart.
>
> 80VDC is enough to make you sit and take notice if you touch it the
> wrong way. It will not harm you however. 24VDC you can't even feel
> even if you are standing in a bucket of salt water.
>
> You really don't have to freak out about harming yourself at these
> voltages. Been there, done that, still alive and none the worse for
> the wear.
>
> Mariss
>
>
>
> --- In CAD_CAM_EDM_DRO@y..., "stevenson_engineers" <machines@n...>
> wrote:
> > >--- In CAD_CAM_EDM_DRO@y..., Keith Green <ksgg@s...> wrote:
> > > Volts don't kill; amps do. Usually the worst is less than
> > > (near towould
> > > your body's current) where it interrupts your heart. Volts
> > >just be thewarning
> > > "penetrating power" of the charge. If you've got bleeding hands
> and
> > >are
> > > standing barefoot in a puddle of salt water, it wouldn't take
> > >much...
> >
> > So if I touch the leads on my big welder that's rated at 35 volt
> 300
> > amp I'm dead?
> > Funny that stick welders are sold over the counter with NO
> ontools
> > them about the danger of getting killed by the output leads.
> >
> > John S.
> > >
> > >
> > > keith
> > > ----- Original Message -----
> > > From: "mayfieldtm" <mayfiet@i...>
> > > To: <CAD_CAM_EDM_DRO@y...>
> > > Sent: Saturday, August 17, 2002 1:58 PM
> > > Subject: [CAD_CAM_EDM_DRO] Shock Warning
> > >
> > >
> > > > --- In CAD_CAM_EDM_DRO@y..., "mariss92705" <mariss92705@y...>
> > wrote:
> > > > >
> > > > > You have to work very hard to get shocked by voltages less
> than
> > > > > 80VDC. It may tickle a little bit but that's about it.
> > > > >
> > > >
> > > > True, but don't forget that human skin is an insulator.
> > > >
> > > > If you-all are like me, whenever I work around machines,
> andthis
> > > > sharp things like chips and tool bits, my hands often have
> > numerous
> > > > cuts.
> > > >
> > > > Be very careful when poking around with electrics with a cut
> > finger.
> > > > Even 12 volts can be lethel under just the wrong conditions.
> > > > Or so I've heard, (could be just a tall tail)
> > > > If nothing else, it might make you do the Jig.
> > > >
> > > > Tom M. :~(
> > > >
> > > >
> > > >
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if
> > > you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider
> > as ahttp://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > sister site to the CCED group, as many of the same members are
> > there, for OT
> > > subjects, that are not allowed on the CCED list.
> > > >
> > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > POSTING THEM.
> > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > >
> > > > Post messages: CAD_CAM_EDM_DRO@y...
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > > Moderator: jmelson@a... timg@k... [Moderator]
> > > > URL to this group:
> > > > bill,
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > >
> > > > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> > > >
> > > >
Discussion Thread
Lloyd Leung
2002-08-15 21:03:45 UTC
Here's my proposed power supply setup.
mariss92705
2002-08-16 01:13:19 UTC
Re: Here's my proposed power supply setup.
rawen2
2002-08-16 09:43:38 UTC
Q for Mariss (was Re: Here's my proposed power supply setup.)
mayfieldtm
2002-08-16 09:45:38 UTC
Re: Here's my proposed power supply setup.
JJ
2002-08-16 12:58:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
JJ
2002-08-16 13:02:50 UTC
RE: [CAD_CAM_EDM_DRO] Q for Mariss (was Re: Here's my proposed power supply setup.)
mayfieldtm
2002-08-16 14:53:34 UTC
Re: Here's my proposed power supply setup.
turbulatordude
2002-08-16 15:37:50 UTC
Q for Mariss (was Re: Here's my proposed power supply setup.)
mariss92705
2002-08-16 18:32:01 UTC
Re: Here's my proposed power supply setup.
mariss92705
2002-08-16 18:42:42 UTC
Q for Mariss (was Re: Here's my proposed power supply setup.)
Jon Elson
2002-08-16 21:35:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
Lloyd Leung
2002-08-16 22:05:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
andrewyslee
2002-08-16 22:30:11 UTC
quickie LED lesson
Lloyd Leung
2002-08-16 22:36:13 UTC
RE: [CAD_CAM_EDM_DRO] quickie LED lesson
turbulatordude
2002-08-17 06:31:37 UTC
Re: Here's my proposed power supply setup.
Les Watts
2002-08-17 07:25:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
JJ
2002-08-17 09:36:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
mariss92705
2002-08-17 11:56:07 UTC
Re: Here's my proposed power supply setup.
mariss92705
2002-08-17 12:01:00 UTC
Re: Here's my proposed power supply setup.
Mike
2002-08-17 12:51:50 UTC
RE: [CAD_CAM_EDM_DRO] quickie LED lesson
pcfw
2002-08-17 12:51:50 UTC
Re: quickie LED lesson
Brian
2002-08-17 13:41:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Here's my proposed power supply setup.
mayfieldtm
2002-08-17 13:59:01 UTC
Shock Warning
JJ
2002-08-17 14:32:15 UTC
RE: [CAD_CAM_EDM_DRO] Shock Warning
Matt Shaver
2002-08-17 19:31:26 UTC
Re: [CAD_CAM_EDM_DRO] Shock Warning
JanRwl@A...
2002-08-17 20:03:43 UTC
Re: [CAD_CAM_EDM_DRO] quickie LED lesson
turbulatordude
2002-08-17 20:30:15 UTC
Re: Shock Warning
Keith Green
2002-08-17 20:51:02 UTC
Re: [CAD_CAM_EDM_DRO] Shock Warning
mayfieldtm
2002-08-18 00:19:02 UTC
Re: Shock Warning
stevenson_engineers
2002-08-18 01:43:55 UTC
Re: Shock Warning
mariss92705
2002-08-18 04:10:55 UTC
Re: Shock Warning
stevenson_engineers
2002-08-18 04:30:11 UTC
Re: Shock Warning
bjammin@i...
2002-08-18 04:35:56 UTC
Re: [CAD_CAM_EDM_DRO] Shock Warning
bjammin@i...
2002-08-18 04:36:07 UTC
waaaay OT
JJ
2002-08-18 05:33:10 UTC
RE: [CAD_CAM_EDM_DRO] Shock Warning
turbulatordude
2002-08-18 06:21:07 UTC
Re: waaaay OT
Mike
2002-08-18 06:33:12 UTC
RE: [CAD_CAM_EDM_DRO] quickie LED lesson
mayfieldtm
2002-08-18 09:08:05 UTC
Re: quickie LED lesson
Ian W. Wright
2002-08-18 09:38:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
Clinton Driggars
2002-08-18 11:48:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
wanliker@a...
2002-08-18 12:06:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
JanRwl@A...
2002-08-18 13:39:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
JanRwl@A...
2002-08-18 14:00:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: waaaay OT
JanRwl@A...
2002-08-18 14:04:06 UTC
Re: [CAD_CAM_EDM_DRO] quickie LED lesson
George Wealleans
2002-08-18 15:20:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
wanliker@a...
2002-08-18 16:59:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: waaaay OT
cncnovice
2002-08-18 17:28:01 UTC
Re: Shock Warning
Keith Green
2002-08-18 17:41:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
Zoran A. Scepanovic
2002-08-19 01:24:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shock Warning
bjammin@i...
2002-08-19 02:56:12 UTC
waaaay waaaaay beyond OT
caudlet
2002-08-19 05:35:14 UTC
Re: Shock Warning