CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] G201-IP

on 2002-11-27 02:39:42 UTC
mariss92705 wrote:
> I have breadboarded a protection circuit for the G201. It protects
> against:
>
> 1) Shorting any or all motor wires to ground.
> 2) Shorting any motor phase to phase.
> 3) Miss-phased motors (series or parallel).
> 4) Miss-connected motors.
> 5) Internal motor winding shorts (serial-killer motors).
> 6) Motor connects/disconnects while under power.
> 7) Motor winding short to motor case.
> 8) Unused 6-wire motor leads touching/shorting anywhere.
>
> These are the most common drive failure problems (>95%) that we see
> for return/repair.

Good idea. But what about protection against supply disconnect (fuse
blown)? An additional zener diode would do that turns one of the power
transistors on and clips the voltage peak out of the motor inductance
when this happens. Of course there is the risk that users with
undersized buffering elkos trigger this curcuit too often and overheat
the transistor.

Ciao
Bene

--
!!! Achtung, neue Adresse !!!
Benezan Electronics, Maria-Merian-Str. 5, 70736 Fellbach, Germany
Kundenspezifische Elektronikentwicklung, Sondermaschinenbau

Discussion Thread

mariss92705 2002-11-23 13:41:41 UTC G201-IP Jim Brown 2002-11-23 14:38:41 UTC Re: [CAD_CAM_EDM_DRO] G201-IP Keith Bowers 2002-11-23 14:47:54 UTC Re: [CAD_CAM_EDM_DRO] G201-IP mariss92705 2002-11-23 15:16:28 UTC Re: G201-IP Kory Hamzeh 2002-11-23 15:34:13 UTC RE: [CAD_CAM_EDM_DRO] G201-IP James Cullins 2002-11-23 16:10:41 UTC Re: [CAD_CAM_EDM_DRO] G201-IP turbulatordude 2002-11-23 16:39:34 UTC Re: G201-IP Ron Kline 2002-11-23 18:55:17 UTC Re: [CAD_CAM_EDM_DRO] G201-IP Peter 2002-11-23 19:15:50 UTC Re: [CAD_CAM_EDM_DRO] G201-IP kdoney_63021 2002-11-23 20:14:53 UTC Re: G201-IP Tony Jeffree 2002-11-23 22:02:41 UTC Re: G201-IP deanc500 2002-11-23 23:24:17 UTC Re: G201-IP galt1x 2002-11-24 03:25:56 UTC Re: [CAD_CAM_EDM_DRO] G201-IP Thomas E. Jones 2002-11-24 10:00:20 UTC Re: G201-IP JanRwl@A... 2002-11-24 12:37:38 UTC Re: [CAD_CAM_EDM_DRO] G201-IP JanRwl@A... 2002-11-24 12:46:18 UTC Re: [CAD_CAM_EDM_DRO] Re: G201-IP John Johnson 2002-11-24 13:50:16 UTC Re: [CAD_CAM_EDM_DRO] Re: G201-IP Carol & Jerry Jankura 2002-11-24 14:43:10 UTC RE: [CAD_CAM_EDM_DRO] Re: G201-IP turbulatordude 2002-11-24 20:01:56 UTC Re: G201-IP turbulatordude 2002-11-24 20:03:58 UTC Re: G201-IP turbulatordude 2002-11-24 20:06:17 UTC Re: G201-IP mariss92705 2002-11-24 22:51:31 UTC Re: G201-IP jmkasunich 2002-11-25 06:39:20 UTC Re: G201-IP jmkasunich 2002-11-25 07:02:22 UTC Re: G201-IP n4onl 2002-11-25 08:02:51 UTC Re: G201-IP pt_green 2002-11-25 21:58:41 UTC Re: G201-IP mayfieldtm 2002-11-26 12:58:24 UTC Re: G201-IP mariss92705 2002-11-26 17:46:31 UTC Re: G201-IP Marv Frankel 2002-11-26 18:21:28 UTC Re: [CAD_CAM_EDM_DRO] Re: G201-IP Jon Elson 2002-11-26 23:42:17 UTC Re: [CAD_CAM_EDM_DRO] Re: G201-IP Nicolas Benezan 2002-11-27 02:39:42 UTC Re: [CAD_CAM_EDM_DRO] G201-IP