CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control?

on 2003-07-30 21:37:47 UTC
Hi Rich,

Thanks for the info. The information on the screen sounds very
complete. It doesn't sound like the control is all that complicated in
regards to backsteping.

Thanks in advance for the pix.

Alan KM6VV

RichD wrote:
>
> Alan,
> I don't know what it senses to decide to reverse the cut. But it usually
> happens at the end of the toolpath when the normal cut condition suddenly
> changes as the scrap drops and the cut current disappears or shorts.
> I suppose a timeout for this is taken if nothing returns to normal quickly
> and halts the prog.
> This may happen just as the last block is read and the machine has not quite
> reached the commanded position. Also, dirty material and gaps between
> sandwiched stacked pieces can cause backups and breaks.
> This machine is servo driven x-y 15 x 15" and u-v 5 x 5" (upper axis')
> Once you get the fastest optimum cut speed set, after well into the material,
> the speed is fairly constant, but still being watched by the controller for
> shorts, breaks and anything that cannot support the set speed (condition).
> The video display shows a dynamic bar meter of the voltage, cut speed in
> "/min and several other parametrs. There are many other "pages" that show the
> program progression, files, internal computer settings, back plot (with a dot
> following the actual cut progress) and machine home and fixture offset coordinates.
> Just a look at these screen shots are good to glean info from.
> The O/S is DOS. No hard drive.
> I will select a few shots & send them on direct. Anyone else?
> RichD
>

Discussion Thread

kdntool 2003-07-28 11:54:02 UTC EMC W/PCI card Kim Lux 2003-07-28 12:03:45 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Matt Shaver 2003-07-28 12:05:40 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Paul 2003-07-28 12:15:45 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Kim Lux 2003-07-28 12:40:42 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Tony Jeffree 2003-07-28 14:24:04 UTC Software for wire EDM control? Graham Stabler 2003-07-28 15:59:33 UTC Re: Software for wire EDM control? glee@i... 2003-07-28 16:48:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tony Jeffree 2003-07-29 00:58:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Fred Smith 2003-07-29 05:18:34 UTC Re: Software for wire EDM control? Jon Elson 2003-07-29 10:34:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 10:45:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 10:54:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tony Jeffree 2003-07-29 13:24:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tony Jeffree 2003-07-29 13:24:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? turbulatordude 2003-07-29 13:50:59 UTC Re: Software for wire EDM control? X-Y Tim Goldstein 2003-07-29 13:57:20 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Fred Smith 2003-07-29 14:10:22 UTC Re: Software for wire EDM control? Graham Stabler 2003-07-29 15:28:04 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 16:06:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 16:17:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 16:24:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Dan Mauch 2003-07-29 18:33:12 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tim Goldstein 2003-07-29 18:56:27 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 19:00:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? IMService 2003-07-29 19:00:49 UTC Re: Re: Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 19:36:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Raymond Heckert 2003-07-29 22:00:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-29 22:31:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-29 22:36:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-29 22:38:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? X-Y Tony Jeffree 2003-07-29 22:58:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-07-29 23:12:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 02:50:04 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 06:01:29 UTC Re: Software for wire EDM control? Carol & Jerry Jankura 2003-07-30 06:16:26 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Zafar Salam 2003-07-30 07:03:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Zafar Salam 2003-07-30 07:11:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 08:14:43 UTC Re: Software for wire EDM control? Tony Jeffree 2003-07-30 08:44:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? turbulatordude 2003-07-30 08:58:09 UTC Re: Software for wire EDM control? X-Y Jon Elson 2003-07-30 09:39:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-30 09:44:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 10:50:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Dan Mauch 2003-07-30 10:58:09 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 11:04:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 11:11:39 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 11:13:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 11:23:27 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 11:54:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 12:06:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 13:17:18 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 14:47:01 UTC Re: Software for wire EDM control? Matt Shaver 2003-07-30 15:48:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 15:48:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 16:07:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 16:34:35 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 16:59:49 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 17:08:07 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 17:59:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Peter L. Peres 2003-07-30 18:01:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 19:23:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-07-30 21:04:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-07-30 21:04:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Raymond Heckert 2003-07-30 21:24:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 21:37:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Zafar Salam 2003-07-30 21:40:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Michael 2003-07-31 00:45:56 UTC RE: [CAD_CAM_EDM_DRO] Re: Dolphin Wire EDM Software turbulatordude 2003-07-31 08:12:36 UTC Re: Software for wire EDM control? posting pics Graham Stabler 2003-07-31 08:51:29 UTC Re: Software for wire EDM control? posting pics turbulatordude 2003-07-31 09:42:12 UTC Re: Software for wire EDM control? posting pics - new EDM site Alan Marconett KM6VV 2003-07-31 11:03:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-08-01 03:12:59 UTC Re: Software for wire EDM control? posting pics - new EDM site Tim Goldstein 2003-08-01 10:43:50 UTC RE: [CAD_CAM_EDM_DRO] Re: DIY Three Axis DRO Kit Peter L. Peres 2003-08-01 10:44:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-08-01 17:45:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control?