CAD CAM EDM DRO - Yahoo Group Archive

Re: Re: Re: Software for wire EDM control?

Posted by IMService
on 2003-07-29 19:00:49 UTC
> Date: Tue, 29 Jul 2003 16:23:58 -0700
> From: Alan Marconett KM6VV <KM6VV@...>
>Subject: Re: Re: Software for wire EDM control?
>
>Hi Fred,
>
>Thanks for the interesting info. Sounds like a little more then the
>average hobbyist would do. Foam wings, on the other hand...
>

Alan

It would actually be an interesting project as it involves some mechanical construction for the wire guides and pulleys, and I would bet that it would not be too tough to write/build something that would backup a thousandth or so out of the hot spot and continue on. I think it would be something like the THC that is being developed for Mach1/2. Just slightly more complicated as the direction would have to be parallel and reverse to the direction of cut, instead of perpendicular. There is no need to back out of the cut, just break the wire with a rapid ( it looks like human hair, blond even as it is usually brass plated.) It may also be possible to detect cutting conditions by the tension of the wire, in addition to current.

I know that Ahha will support 4 linear axes and assume that most other commercial/hobby programs can do it as well. 4 linear is much simpler than 3 linear and a rotary. A servo drive might be in order if you could trick the encoder signals to make the following error go negative or positive by some delta, based on the cutting conditions. With a very little Cam trickery, you could also feed lines to the controller that are just about the size of the machine resolution. G01 X.001, are we there yet? Back up a little and try again.

Best Regards, Fred Smith- IMService

Listserve Special discounts and offers are at:
http://www.imsrv.com/hobby

We are THE source for low cost Cad Cam

Discussion Thread

kdntool 2003-07-28 11:54:02 UTC EMC W/PCI card Kim Lux 2003-07-28 12:03:45 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Matt Shaver 2003-07-28 12:05:40 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Paul 2003-07-28 12:15:45 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Kim Lux 2003-07-28 12:40:42 UTC Re: [CAD_CAM_EDM_DRO] EMC W/PCI card Tony Jeffree 2003-07-28 14:24:04 UTC Software for wire EDM control? Graham Stabler 2003-07-28 15:59:33 UTC Re: Software for wire EDM control? glee@i... 2003-07-28 16:48:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tony Jeffree 2003-07-29 00:58:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Fred Smith 2003-07-29 05:18:34 UTC Re: Software for wire EDM control? Jon Elson 2003-07-29 10:34:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 10:45:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 10:54:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tony Jeffree 2003-07-29 13:24:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tony Jeffree 2003-07-29 13:24:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? turbulatordude 2003-07-29 13:50:59 UTC Re: Software for wire EDM control? X-Y Tim Goldstein 2003-07-29 13:57:20 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Fred Smith 2003-07-29 14:10:22 UTC Re: Software for wire EDM control? Graham Stabler 2003-07-29 15:28:04 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 16:06:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 16:17:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 16:24:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Dan Mauch 2003-07-29 18:33:12 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Tim Goldstein 2003-07-29 18:56:27 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 19:00:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? IMService 2003-07-29 19:00:49 UTC Re: Re: Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-29 19:36:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Raymond Heckert 2003-07-29 22:00:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-29 22:31:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-29 22:36:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-29 22:38:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? X-Y Tony Jeffree 2003-07-29 22:58:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-07-29 23:12:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 02:50:04 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 06:01:29 UTC Re: Software for wire EDM control? Carol & Jerry Jankura 2003-07-30 06:16:26 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Zafar Salam 2003-07-30 07:03:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Zafar Salam 2003-07-30 07:11:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 08:14:43 UTC Re: Software for wire EDM control? Tony Jeffree 2003-07-30 08:44:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? turbulatordude 2003-07-30 08:58:09 UTC Re: Software for wire EDM control? X-Y Jon Elson 2003-07-30 09:39:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Jon Elson 2003-07-30 09:44:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 10:50:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Dan Mauch 2003-07-30 10:58:09 UTC RE: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 11:04:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 11:11:39 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 11:13:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 11:23:27 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 11:54:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 12:06:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 13:17:18 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 14:47:01 UTC Re: Software for wire EDM control? Matt Shaver 2003-07-30 15:48:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 15:48:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 16:07:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-07-30 16:34:35 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 16:59:49 UTC Re: Software for wire EDM control? Fred Smith 2003-07-30 17:08:07 UTC Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 17:59:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Peter L. Peres 2003-07-30 18:01:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 19:23:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-07-30 21:04:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-07-30 21:04:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Raymond Heckert 2003-07-30 21:24:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Alan Marconett KM6VV 2003-07-30 21:37:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Zafar Salam 2003-07-30 21:40:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Michael 2003-07-31 00:45:56 UTC RE: [CAD_CAM_EDM_DRO] Re: Dolphin Wire EDM Software turbulatordude 2003-07-31 08:12:36 UTC Re: Software for wire EDM control? posting pics Graham Stabler 2003-07-31 08:51:29 UTC Re: Software for wire EDM control? posting pics turbulatordude 2003-07-31 09:42:12 UTC Re: Software for wire EDM control? posting pics - new EDM site Alan Marconett KM6VV 2003-07-31 11:03:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? Graham Stabler 2003-08-01 03:12:59 UTC Re: Software for wire EDM control? posting pics - new EDM site Tim Goldstein 2003-08-01 10:43:50 UTC RE: [CAD_CAM_EDM_DRO] Re: DIY Three Axis DRO Kit Peter L. Peres 2003-08-01 10:44:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control? RichD 2003-08-01 17:45:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Software for wire EDM control?