Re: Yeager CNC Pro and relay settings
Posted by
shelbyshepherd2002
on 2003-07-31 13:21:40 UTC
Hi Alan,fortino,
I had wired my machine from your wiring diagram Alan, (very easy to
follow, thank you)
I forgot to mention, had a dwell time in the test code between M01
(on)and M05 (off), when it got to M01 line the LED was off and come
on at the dwell line and off on the M04 line.
There was no reading on a test meter on any lines.
The setting is on "default" which is HIGH in CNC Pro.
There is no resistor installed, is this really necessory on your
wiring diagram Alan?
Shelby
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett KM6VV
<KM6VV@a...> wrote:
reach it if you have trouble.
are there, for OT subjects, that are not allowed on the CCED list.
EXCEPTIONS........
I had wired my machine from your wiring diagram Alan, (very easy to
follow, thank you)
I forgot to mention, had a dwell time in the test code between M01
(on)and M05 (off), when it got to M01 line the LED was off and come
on at the dwell line and off on the M04 line.
There was no reading on a test meter on any lines.
The setting is on "default" which is HIGH in CNC Pro.
There is no resistor installed, is this really necessory on your
wiring diagram Alan?
Shelby
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett KM6VV
<KM6VV@a...> wrote:
> Hi Fortino, Shelby,current.
>
> To drive a load like a SSS, you want the parallel port to SINK
> Some parallel ports cannot SOURCE current as you describe.turn
>
> I suggest you connect the + of the SSS to +5V, and pin 1 to the -
> terminal. then when the pin goes low (>.5V or so), the SSS will
> on.enabled). The
>
> My DriverPS PDF in the files of this group might be of help:
>
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/DriverPS/
>
> HTH
>
> Alan KM6VV
> SherlineCNC
>
> fortino wrote:
> >
> > First, Pin 1 should be +5 V when it is turn on (set high when
> > negative should go to the logic ground.resistor). Just in
> > Don't forget to put small resistance ( I use 0.5-1 ohm
> > case you short your parallel port output.to turn off
> >
> > Second, to turn on the Output 1 the G code should be M03, while
> > the Output 1 the G code is M05.state
> >
> > Fortino
> >
> > ----- Original Message -----
> > From: "shelbyshepherd2002" <cabrillo_shepherd@m...>
> > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > Sent: Thursday, July 31, 2003 4:53 PM
> > Subject: [CAD_CAM_EDM_DRO] Yeager CNC Pro and relay settings
> >
> > > Hi all,
> > >
> > > I need some help on the settings within CNC pro for a solid
> > > relay to activate a solinoid.positive
> > > It is using pin 1 to the neg on the relay and 5 volt to
> > > from games port, should it be set on high or low?did not
> > > This is the sample G code I used to test with but the relay
> > > appear to work.wanliker@a...,
> > >
> > > G01 X5 Y5
> > > M01 (to turn on)
> > > M0 (to turn off)
> > > X0 Y0
> > >
> > > Any ideas welcome on settings or a sample G code to test with.
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > timg@k...http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > Moderator: pentam@c... indigo_red@q... [Moderators]
> > > URL to this group:
> > >reach it if
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > you have trouble.this to be a
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider
> > sister site to the CCED group, as many of the same members arethere, for OT
> > subjects, that are not allowed on the CCED list.POSTING THEM.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........http://docs.yahoo.com/info/terms/
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> > >wanliker@a..., timg@k...
> > >
> > >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > Moderator: pentam@c... indigo_red@q... [Moderators]aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
reach it if you have trouble.
> > http://www.metalworking.com/news_servers.htmlto be a sister site to the CCED group, as many of the same members
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
are there, for OT subjects, that are not allowed on the CCED list.
> >POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
EXCEPTIONS........
> > billhttp://docs.yahoo.com/info/terms/
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
Discussion Thread
shelbyshepherd2002
2003-07-31 02:53:06 UTC
Yeager CNC Pro and relay settings
fortino
2003-07-31 06:36:00 UTC
Re: [CAD_CAM_EDM_DRO] Yeager CNC Pro and relay settings
Torsten
2003-07-31 11:21:53 UTC
Re: Yeager CNC Pro and relay settings
Alan Marconett KM6VV
2003-07-31 11:46:24 UTC
Re: [CAD_CAM_EDM_DRO] Yeager CNC Pro and relay settings
shelbyshepherd2002
2003-07-31 13:21:40 UTC
Re: Yeager CNC Pro and relay settings
Alan Marconett KM6VV
2003-07-31 15:46:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings
fortino
2003-07-31 16:04:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings
Raymond Heckert
2003-07-31 18:22:55 UTC
Re: [CAD_CAM_EDM_DRO] Yeager CNC Pro and relay settings
shelbyshepherd2002
2003-08-01 01:35:51 UTC
Re: Yeager CNC Pro and relay settings
Alan Marconett KM6VV
2003-08-01 10:21:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings
shelbyshepherd2002
2003-08-01 14:19:45 UTC
Re: Yeager CNC Pro and relay settings
Alan Marconett KM6VV
2003-08-01 15:23:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings
James Cullins
2003-08-01 20:41:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings
shelbyshepherd2002
2003-08-01 21:08:29 UTC
Re: Yeager CNC Pro and relay settings
James Cullins
2003-08-01 21:21:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings
markpowerplus
2003-08-03 14:10:23 UTC
Re: Yeager CNC Pro and relay settings
shelbyshepherd2002
2003-08-05 02:24:07 UTC
Re: Yeager CNC Pro and relay settings
Jon Elson
2003-08-05 10:43:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings