Re: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings

Shelby,

To add dwell time, you just write your G-code like this:

M03 G4 P1000 ( turn on output 1, dwell for 1 sec).
M05 G4 P500 ( turn off output 1,dwell for 1/2 sec).

Fortino

----- Original Message -----
From: "shelbyshepherd2002" <cabrillo_shepherd@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Friday, August 01, 2003 3:21 AM
Subject: [CAD_CAM_EDM_DRO] Re: Yeager CNC Pro and relay settings


> Hi Alan,fortino,
>
> I had wired my machine from your wiring diagram Alan, (very easy to
> follow, thank you)
> I forgot to mention, had a dwell time in the test code between M01
> (on)and M05 (off), when it got to M01 line the LED was off and come
> on at the dwell line and off on the M04 line.
> There was no reading on a test meter on any lines.
> The setting is on "default" which is HIGH in CNC Pro.
> There is no resistor installed, is this really necessory on your
> wiring diagram Alan?
>
> Shelby
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett KM6VV
> <KM6VV@a...> wrote:
> > Hi Fortino, Shelby,
> >
> > To drive a load like a SSS, you want the parallel port to SINK
> current.
> > Some parallel ports cannot SOURCE current as you describe.
> >
> > I suggest you connect the + of the SSS to +5V, and pin 1 to the -
> > terminal. then when the pin goes low (>.5V or so), the SSS will
> turn
> > on.
> >
> > My DriverPS PDF in the files of this group might be of help:
> >
> > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/DriverPS/
> >
> > HTH
> >
> > Alan KM6VV
> > SherlineCNC
> >
> > fortino wrote:
> > >
> > > First, Pin 1 should be +5 V when it is turn on (set high when
> enabled). The
> > > negative should go to the logic ground.
> > > Don't forget to put small resistance ( I use 0.5-1 ohm
> resistor). Just in
> > > case you short your parallel port output.
> > >
> > > Second, to turn on the Output 1 the G code should be M03, while
> to turn off
> > > the Output 1 the G code is M05.
> > >
> > > Fortino
> > >
> > > ----- Original Message -----
> > > From: "shelbyshepherd2002" <cabrillo_shepherd@m...>
> > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > Sent: Thursday, July 31, 2003 4:53 PM
> > > Subject: [CAD_CAM_EDM_DRO] Yeager CNC Pro and relay settings
> > >
> > > > Hi all,
> > > >
> > > > I need some help on the settings within CNC pro for a solid
> state
> > > > relay to activate a solinoid.
> > > > It is using pin 1 to the neg on the relay and 5 volt to
> positive
> > > > from games port, should it be set on high or low?
> > > > This is the sample G code I used to test with but the relay
> did not
> > > > appear to work.
> > > >
> > > > G01 X5 Y5
> > > > M01 (to turn on)
> > > > M0 (to turn off)
> > > > X0 Y0
> > > >
> > > > Any ideas welcome on settings or a sample G code to test with.
> > > >
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > >
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@a...,
> > > timg@k...
> > > > Moderator: pentam@c... indigo_red@q... [Moderators]
> > > > URL to this group:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if
> > > you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider
> this to be a
> > > sister site to the CCED group, as many of the same members are
> there, for OT
> > > subjects, that are not allowed on the CCED list.
> > > >
> > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING THEM.
> > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > > bill
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > >
> > > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> > > >
> > > >
> > > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@a..., timg@k...
> > > Moderator: pentam@c... indigo_red@q... [Moderators]
> > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this
> to be a sister site to the CCED group, as many of the same members
> are there, for OT subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>