CAD CAM EDM DRO - Yahoo Group Archive

Re: Re: re:hand jive

Posted by ballendo@y...
on 2000-11-03 17:57:27 UTC
Jon,

Excellent points! Nice post!

Ballendo

P.S. I wonder what the guys fifty years from now will say, when they
have been "raised up" using jog buttons and jogwheels, instead of the
handwheels WE began with??? I really do believe you "feel" its
faster because you have been "programmed" by your experience to
believe so, and therefore it IS faster for you! Notice I'm not
disputing your claim to doing some things faster by hand control;
just wondering if you'd feel the same if all your past experience
was "cut by wire"???


>There most certainly ARE times manual machining is faster.<snip>

>Be aware, if you have ballscrews, you have lost the ability to treat
>your CNC mill the same as an acme fitted manual!!! Cutter forces are
>more than enough to back drive ball screws and powered down servo
>motors!!! Under the right conditions, a 1/4" end mill or even smaller
>can move things around, a 1/2" or larger can cause you to ruin a set
>of shorts if it takes a big hop in the wrong direction.
>Where this will bite you but good is going into an inside corner
>while climb cutting. Trust me on this one.
>Jon

Discussion Thread

jmw@c... 2000-11-02 18:31:54 UTC hand jive Jon Anderson 2000-11-02 21:41:53 UTC Re: [CAD_CAM_EDM_DRO] hand jive Darrell 2000-11-02 22:26:36 UTC Re: [CAD_CAM_EDM_DRO] hand jive ballendo@y... 2000-11-03 00:03:51 UTC re:hand jive Smoke 2000-11-03 00:16:23 UTC Re: [CAD_CAM_EDM_DRO] re:hand jive Wally K 2000-11-03 00:47:42 UTC Re: re:hand jive ballendo@y... 2000-11-03 00:52:19 UTC Re: re:hand jive ballendo@y... 2000-11-03 01:05:23 UTC RE:Re: re:hand jive ptengin@a... 2000-11-03 02:14:38 UTC Re: [CAD_CAM_EDM_DRO] re:hand jive Jon Anderson 2000-11-03 07:03:44 UTC Re: [CAD_CAM_EDM_DRO] Re: re:hand jive Jon Anderson 2000-11-03 07:07:07 UTC Re: [CAD_CAM_EDM_DRO] RE:Re: re:hand jive dave engvall 2000-11-03 08:50:15 UTC Re: [CAD_CAM_EDM_DRO] RE:Re: re:hand jive Ray 2000-11-03 10:37:18 UTC Re: Re: RE:Re: re:hand jive Alan Marconett KM6VV 2000-11-03 11:01:32 UTC re:hand jive Jon Elson 2000-11-03 11:39:32 UTC Re: [CAD_CAM_EDM_DRO] re:hand jive JanRwl@A... 2000-11-03 16:45:15 UTC Re: [CAD_CAM_EDM_DRO] re:hand jive JanRwl@A... 2000-11-03 16:49:33 UTC Re: [CAD_CAM_EDM_DRO] re:hand jive ballendo@y... 2000-11-03 17:57:27 UTC Re: Re: re:hand jive Jon Anderson 2000-11-03 18:46:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: re:hand jive ballendo@y... 2000-11-03 20:43:33 UTC Re: re: rE: RE:hand jive Jon Anderson 2000-11-03 21:41:06 UTC Re: [CAD_CAM_EDM_DRO] Re: re: rE: RE:hand jive Smoke 2000-11-03 21:53:11 UTC Re: [CAD_CAM_EDM_DRO] Re: re: rE: RE:hand jive Darrell 2000-11-04 00:13:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: re:hand jive John Stevenson 2000-11-04 02:02:27 UTC Re: re:hand jive dave engvall 2000-11-04 07:12:23 UTC Re: [CAD_CAM_EDM_DRO] Re: re:hand jive dougrasmussen@c... 2000-11-04 08:10:11 UTC Re: rE: RE:hand jive ballendo@y... 2000-11-04 14:37:17 UTC re:Re: rE: RE:hand jive Brian Pitt 2000-11-04 15:05:08 UTC Re: [CAD_CAM_EDM_DRO] re:Re: rE: RE:hand jive Jon Anderson 2000-11-04 15:07:30 UTC Re: [CAD_CAM_EDM_DRO] RE:hand jive Randy Gordon-Gilmore 2000-11-04 15:28:55 UTC Controllers, was RE:hand jive Wally K 2000-11-04 15:29:03 UTC re:Re: rE: RE:hand jive Jon Anderson 2000-11-04 15:54:29 UTC Re: [CAD_CAM_EDM_DRO] re:Re: rE: RE:hand jive Brian Pitt 2000-11-04 15:55:35 UTC Re: [CAD_CAM_EDM_DRO] Controllers, was RE:hand jive Randy Gordon-Gilmore 2000-11-04 16:01:32 UTC Knob control, was re:hand jive Randy Gordon-Gilmore 2000-11-04 16:15:13 UTC Re: Controllers, was RE:hand jive Darrell 2000-11-04 17:05:19 UTC Re: [CAD_CAM_EDM_DRO] Re: re:hand jive Darrell 2000-11-04 17:08:23 UTC Re: [CAD_CAM_EDM_DRO] Re: re:hand jive ptengin@a... 2000-11-04 17:12:27 UTC Re: [CAD_CAM_EDM_DRO] re:Re: rE: RE:hand jive Jon Anderson 2000-11-04 17:23:52 UTC Re: [CAD_CAM_EDM_DRO] Re: re:hand jive Jon Anderson 2000-11-04 17:48:29 UTC Re: [CAD_CAM_EDM_DRO] re:Re: rE: RE:hand jive Alan Marconett KM6VV 2000-11-04 20:00:39 UTC RE:hand jive Alan Marconett KM6VV 2000-11-04 20:29:35 UTC re:hand jive Brian Pitt 2000-11-04 21:20:40 UTC Re: [CAD_CAM_EDM_DRO] RE:hand jive Darrell 2000-11-04 22:08:30 UTC Re: [CAD_CAM_EDM_DRO] re:hand jive Hugh Mahlendorf 2000-11-05 09:50:26 UTC Re: [CAD_CAM_EDM_DRO] re:Re: rE: RE:hand jive Anne Ogborn 2000-11-05 10:38:05 UTC Re: [CAD_CAM_EDM_DRO] Re: re:hand jive Anne Ogborn 2000-11-05 10:52:10 UTC Re: [CAD_CAM_EDM_DRO] re:Re: rE: RE:hand jive Anne Ogborn 2000-11-05 10:59:52 UTC Re: [CAD_CAM_EDM_DRO] Knob control, was re:hand jive Anne Ogborn 2000-11-05 11:05:11 UTC Re: [CAD_CAM_EDM_DRO] Re: re:hand jive Jeff Barlow 2000-11-05 12:39:02 UTC Re: [CAD_CAM_EDM_DRO] Knob control, was re:hand jive Alan Marconett KM6VV 2000-11-05 14:20:38 UTC RE:hand jive Brian Pitt 2000-11-05 16:27:57 UTC Re: [CAD_CAM_EDM_DRO] RE:hand jive Jon Elson 2000-11-05 22:01:42 UTC Re: [CAD_CAM_EDM_DRO] re:Re: rE: RE:hand jive Alan Marconett KM6VV 2000-11-06 11:14:31 UTC RE:hand jive diazden 2000-11-06 14:43:13 UTC Re: [CAD_CAM_EDM_DRO] RE:hand jive