Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Posted by
Joe Vicars
on 2001-02-19 09:15:22 UTC
Jon,
What brand/type of tape did you use?
Jon Anderson wrote:
What brand/type of tape did you use?
Jon Anderson wrote:
> Joe,
>
> You will be surprised what you can do with double sided tape. Your
> biggest problem using it might be getting your parts free when you are
> done. I recently machined a 6 x 12 x 3/8 plate of delrin using tape.
> There were three rectangular pockets that really skeletonized the plate.
> I drilled the four corner holes first, then set it on a large plate of
> acrylic with pins matching the 4 holes. This was more for location since
> I had to machine both sides. The tape did all the holding, and it was a
> slow process prying the part off when I was done. You might want to lay
> the tape down first, then press your hand on the tape where you would be
> putting the parts. This will reduce the holding power.
>
> Jon
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
Discussion Thread
Joe Vicars
2001-02-19 06:36:24 UTC
Holding thin sheet
Jon Anderson
2001-02-19 07:36:28 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Joe Vicars
2001-02-19 09:15:22 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Jon Anderson
2001-02-19 10:22:05 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
William Scalione
2001-02-19 10:46:44 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Alan Marconett KM6VV
2001-02-19 10:51:02 UTC
Re: Holding thin sheet
indigo_red@q...
2001-02-19 11:37:38 UTC
Re: Holding thin sheet
Brian Pitt
2001-02-19 13:52:09 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
A. G. Eckstein
2001-02-19 14:37:45 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Doug Harrison
2001-02-19 16:22:48 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Hugh Currin
2001-02-19 16:51:53 UTC
Re: Holding thin sheet
tauseef
2001-02-19 17:32:36 UTC
Re: Holding thin sheet
Rich D.
2001-02-19 18:38:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Rich D.
2001-02-19 18:39:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Marcus & Eva
2001-02-19 20:07:34 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Smoke
2001-02-19 20:55:28 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
ptengin@a...
2001-02-20 02:20:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Dan Mauch
2001-02-20 07:14:56 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
dan.eaton@c...
2001-02-20 07:19:06 UTC
Re: Holding thin sheet
Joe Vicars
2001-02-20 07:31:00 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
ballendo@y...
2001-02-20 20:42:53 UTC
Re: Holding thin sheet
ballendo@y...
2001-02-20 21:00:04 UTC
Re: Holding thin sheet
Jon Anderson
2001-02-20 21:47:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Joe Vicars
2001-02-21 08:54:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Sven Peter, TAD S.A.
2001-02-22 15:10:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Tony Jeffree
2001-02-23 07:46:35 UTC
Re: Holding thin sheet