Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Posted by
ptengin@a...
on 2001-02-20 02:20:25 UTC
In a message dated 2/19/01 9:39:25 AM Hawaiian Standard Time,
indigo_red@... writes:
<< How about a small homemade vacuum table setup. Drill evenly spaced
tiny holes in a sheet of "whatever? alum, Delrin etc"
===== =======|======= ======= ===|
| |------->airflow >> ===== Vacuum source
=================================|
-Lee >>
You need a heck of a big vacuum pump but I know it can be done. Simply drop a
sheet of particle board on top of your vacuum plenum. It will hold down parts
nicely. If you put some double stick tape in there too, you'll have to pry
off your parts.
Peter
THRD, Inc.
indigo_red@... writes:
<< How about a small homemade vacuum table setup. Drill evenly spaced
tiny holes in a sheet of "whatever? alum, Delrin etc"
===== =======|======= ======= ===|
| |------->airflow >> ===== Vacuum source
=================================|
-Lee >>
You need a heck of a big vacuum pump but I know it can be done. Simply drop a
sheet of particle board on top of your vacuum plenum. It will hold down parts
nicely. If you put some double stick tape in there too, you'll have to pry
off your parts.
Peter
THRD, Inc.
Discussion Thread
Joe Vicars
2001-02-19 06:36:24 UTC
Holding thin sheet
Jon Anderson
2001-02-19 07:36:28 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Joe Vicars
2001-02-19 09:15:22 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Jon Anderson
2001-02-19 10:22:05 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
William Scalione
2001-02-19 10:46:44 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Alan Marconett KM6VV
2001-02-19 10:51:02 UTC
Re: Holding thin sheet
indigo_red@q...
2001-02-19 11:37:38 UTC
Re: Holding thin sheet
Brian Pitt
2001-02-19 13:52:09 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
A. G. Eckstein
2001-02-19 14:37:45 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Doug Harrison
2001-02-19 16:22:48 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Hugh Currin
2001-02-19 16:51:53 UTC
Re: Holding thin sheet
tauseef
2001-02-19 17:32:36 UTC
Re: Holding thin sheet
Rich D.
2001-02-19 18:38:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Rich D.
2001-02-19 18:39:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Marcus & Eva
2001-02-19 20:07:34 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Smoke
2001-02-19 20:55:28 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
ptengin@a...
2001-02-20 02:20:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Dan Mauch
2001-02-20 07:14:56 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
dan.eaton@c...
2001-02-20 07:19:06 UTC
Re: Holding thin sheet
Joe Vicars
2001-02-20 07:31:00 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
ballendo@y...
2001-02-20 20:42:53 UTC
Re: Holding thin sheet
ballendo@y...
2001-02-20 21:00:04 UTC
Re: Holding thin sheet
Jon Anderson
2001-02-20 21:47:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Joe Vicars
2001-02-21 08:54:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Sven Peter, TAD S.A.
2001-02-22 15:10:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Tony Jeffree
2001-02-23 07:46:35 UTC
Re: Holding thin sheet