CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet

on 2001-02-22 15:10:07 UTC
In the german groop they talked about to use a refrigerator compresor
for the vaccum hold down plate made out of chip wood.
Personaly I tried it once with a Ventury type generator and id didnt
work well,
but mostly because my seals were to stiff.
Sven Peter

ptengin@... wrote:

> In a message dated 2/19/01 9:39:25 AM Hawaiian Standard Time,
> indigo_red@... writes:
>
> << How about a small homemade vacuum table setup. Drill evenly spaced
> tiny holes in a sheet of "whatever? alum, Delrin etc"
>
> ===== =======|======= ======= ===|
> | |------->airflow >> ===== Vacuum source
> =================================|
>
> -Lee >>
>
> You need a heck of a big vacuum pump but I know it can be done. Simply drop a
> sheet of particle board on top of your vacuum plenum. It will hold down parts
> nicely. If you put some double stick tape in there too, you'll have to pry
> off your parts.
>
> Peter
> THRD, Inc.
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html

[Non-text portions of this message have been removed]

Discussion Thread

Joe Vicars 2001-02-19 06:36:24 UTC Holding thin sheet Jon Anderson 2001-02-19 07:36:28 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet Joe Vicars 2001-02-19 09:15:22 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet Jon Anderson 2001-02-19 10:22:05 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet William Scalione 2001-02-19 10:46:44 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet Alan Marconett KM6VV 2001-02-19 10:51:02 UTC Re: Holding thin sheet indigo_red@q... 2001-02-19 11:37:38 UTC Re: Holding thin sheet Brian Pitt 2001-02-19 13:52:09 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet A. G. Eckstein 2001-02-19 14:37:45 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet Doug Harrison 2001-02-19 16:22:48 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet Hugh Currin 2001-02-19 16:51:53 UTC Re: Holding thin sheet tauseef 2001-02-19 17:32:36 UTC Re: Holding thin sheet Rich D. 2001-02-19 18:38:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet Rich D. 2001-02-19 18:39:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet Marcus & Eva 2001-02-19 20:07:34 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet Smoke 2001-02-19 20:55:28 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet ptengin@a... 2001-02-20 02:20:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet Dan Mauch 2001-02-20 07:14:56 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet dan.eaton@c... 2001-02-20 07:19:06 UTC Re: Holding thin sheet Joe Vicars 2001-02-20 07:31:00 UTC Re: [CAD_CAM_EDM_DRO] Holding thin sheet ballendo@y... 2001-02-20 20:42:53 UTC Re: Holding thin sheet ballendo@y... 2001-02-20 21:00:04 UTC Re: Holding thin sheet Jon Anderson 2001-02-20 21:47:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet Joe Vicars 2001-02-21 08:54:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet Sven Peter, TAD S.A. 2001-02-22 15:10:07 UTC Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet Tony Jeffree 2001-02-23 07:46:35 UTC Re: Holding thin sheet