Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Posted by
Rich D.
on 2001-02-19 18:38:12 UTC
T, and list,
I use 3M #486MP High performance double sided film adhesive.
Comes in large sheets if needed. Make sure surfaces are oil free.
Rich D.
tauseef wrote:
-==Rich=-=Colorado Midland Railway=-=<http://www.geocities.com/cmsteam/>
I use 3M #486MP High performance double sided film adhesive.
Comes in large sheets if needed. Make sure surfaces are oil free.
Rich D.
tauseef wrote:
>--
> hey guys
> I have used superglue and double sided tape also..both work great.
> Joe, I use Scotch 3M tape that you can buy from OfficeMax. Its
> probably more expensive in the long run but it come in a dispenser
> like most of there tapes and is a nice size for smaller work.
> tauseef
>
> --- In CAD_CAM_EDM_DRO@y..., "Doug Harrison" <prototype@c...> wrote:
> > I'll second the motion for double back tape. Works great for thin,
> flexible
> > sheets. You can also use it for holding non-ferrous materials on a
> surface
> > grinder.
> >
> > I cut lots of patterns from thin sheets - mostly .125" aluminum.
> If your
> > machine is capable of holding Z accuracy of .001" you will find it
> easiest
> > to cut to within .002-.005" of the lower surface which leaves a
> paper thin
> > membrane holding the piece in place. We do this with nearly all
> flat sheet
> > parts - even stainless and tool steel. It's less messy than tape
> and the
> > parts just pop out. The flash left attached can be removed with a
> deburring
> > tool. Be careful! Its sharp as a razor.
> >
> > Doug
-==Rich=-=Colorado Midland Railway=-=<http://www.geocities.com/cmsteam/>
Discussion Thread
Joe Vicars
2001-02-19 06:36:24 UTC
Holding thin sheet
Jon Anderson
2001-02-19 07:36:28 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Joe Vicars
2001-02-19 09:15:22 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Jon Anderson
2001-02-19 10:22:05 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
William Scalione
2001-02-19 10:46:44 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Alan Marconett KM6VV
2001-02-19 10:51:02 UTC
Re: Holding thin sheet
indigo_red@q...
2001-02-19 11:37:38 UTC
Re: Holding thin sheet
Brian Pitt
2001-02-19 13:52:09 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
A. G. Eckstein
2001-02-19 14:37:45 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Doug Harrison
2001-02-19 16:22:48 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Hugh Currin
2001-02-19 16:51:53 UTC
Re: Holding thin sheet
tauseef
2001-02-19 17:32:36 UTC
Re: Holding thin sheet
Rich D.
2001-02-19 18:38:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Rich D.
2001-02-19 18:39:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Marcus & Eva
2001-02-19 20:07:34 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
Smoke
2001-02-19 20:55:28 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
ptengin@a...
2001-02-20 02:20:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Dan Mauch
2001-02-20 07:14:56 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
dan.eaton@c...
2001-02-20 07:19:06 UTC
Re: Holding thin sheet
Joe Vicars
2001-02-20 07:31:00 UTC
Re: [CAD_CAM_EDM_DRO] Holding thin sheet
ballendo@y...
2001-02-20 20:42:53 UTC
Re: Holding thin sheet
ballendo@y...
2001-02-20 21:00:04 UTC
Re: Holding thin sheet
Jon Anderson
2001-02-20 21:47:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Joe Vicars
2001-02-21 08:54:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Sven Peter, TAD S.A.
2001-02-22 15:10:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Holding thin sheet
Tony Jeffree
2001-02-23 07:46:35 UTC
Re: Holding thin sheet