CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...

Posted by Vince Negrete
on 2003-01-21 08:27:57 UTC
What is the ideal version or make I should use to make it easier? Does it
matter?
I have SUSE. Has anyone installed EMC on SUSE yet?
I would like to put it on that Linux.. That is, once I get it RTed...
Vince



----- Original Message -----
From: "j.guenther" <j.guenther@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, January 21, 2003 8:15 AM
Subject: RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...


> yes EMC has been ported to dos, it is called Deskncrt and it is available
> from www.deskam.com/download.html and is the third item on the list. It
is
> not the most recent version of EMC but it does a passable job. If you get
> the BDI (Braid Dead Install) version of EMC, from Ray Henry or others that
> distribute it, you can have EMC up and running in under 30 minutes with
not
> hassle what so ever. This is the best way to get EMC up and running,
IMHO,
> and Paul Corner deserves a great deal of thanks for making this happen.
>
> John Guenther
> 'Ye Olde Pen Maker'
> Sterling, Virginia
>
> > -----Original Message-----
> > From: alex [mailto:telecomt@...]
> > Sent: Tuesday, January 21, 2003 10:30 AM
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
> >
> >
> > Hi, just want to point out that Linux is not a real time OS,
> > though it has an excellent system calls for the C programming.
> > Its a very good OS, but requires RT extension for a real time work
> > ( I have to yet figure it out).
> > In this respect I wonder if somebody ported EMC to Dos.
> > Alex
> >
> > ----- Original Message -----
> > From: <dpeter@...>
> > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > Sent: Monday, January 20, 2003 11:15 PM
> > Subject: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
> >
> >
> > > I haven't gone hacking into EMC yet, but has anyone tried to port
> > > it to windows? I normally work in VB and VC++ and as of yet not
> > > played in Linux and haven't even seen a Unix box in 15 years.
> > > What peaked my interest was a previous post that mentioned
> > > IO_base_address. If it works off the I/O address, it should talk
> > > directly to an ISA card just like the parallel port. I have ISA
> > > controller cards, but no developable software so I'm reverse
> > > engineering them to write code. If I can pull g-code conversion from
> > > another piece of software rather than doing it from scratch...
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > > Moderator: pentam@... indigo_red@...
timg@...
> > [Moderator]
> > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if
> > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this to be
a
> > sister site to the CCED group, as many of the same members are
> > there, for OT
> > subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> > >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > Moderator: pentam@... indigo_red@...
> > timg@... [Moderator]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
> > to be a sister site to the CCED group, as many of the same
> > members are there, for OT subjects, that are not allowed on the CCED
list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> > EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> >
> >
> >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: pentam@... indigo_red@... timg@...
[Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>

Discussion Thread

zestronad54529 <dpeter@n... 2003-01-20 20:15:27 UTC EMC, ISA and other Questions... Ivan Nichols <ouisel@v... 2003-01-21 05:12:00 UTC Re: EMC, ISA and other Questions... Dave Lantz 2003-01-21 05:17:38 UTC RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions... Carol & Jerry Jankura 2003-01-21 05:53:07 UTC RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions... Vince Negrete 2003-01-21 07:44:52 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions... alex 2003-01-21 07:50:53 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... j.guenther 2003-01-21 08:15:56 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... alex 2003-01-21 08:23:48 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Vince Negrete 2003-01-21 08:27:57 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... j.guenther 2003-01-21 08:36:48 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... alex 2003-01-21 08:50:25 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Vince Negrete 2003-01-21 08:54:20 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... j.guenther 2003-01-21 09:03:23 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Tim Goldstein 2003-01-21 09:14:34 UTC RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions... j.guenther 2003-01-21 09:18:15 UTC RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions... alex 2003-01-21 09:18:44 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Jon Elson 2003-01-21 09:21:18 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Jon Elson 2003-01-21 09:28:01 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... j.guenther 2003-01-21 09:39:00 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... alex 2003-01-21 09:52:47 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Carol & Jerry Jankura 2003-01-21 10:44:26 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Carol & Jerry Jankura 2003-01-21 10:44:30 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... alex 2003-01-21 11:12:33 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Ray Henry 2003-01-21 13:44:43 UTC Re: EMC, ISA and other Questions... jmkasunich <jmkasunich@y... 2003-01-21 14:53:28 UTC PLEASE TRIM POSTS!! was Re: EMC, ISA and other Questions... Ray Henry 2003-01-21 17:10:00 UTC Re: Re: EMC, ISA and other Questions... Ray Henry 2003-01-21 17:10:03 UTC Re: Re: EMC, ISA and other Questions... Jon Elson 2003-01-21 23:16:20 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Jon Elson 2003-01-21 23:18:01 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Tim Goldstein 2003-01-21 23:27:54 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Matt Shaver 2003-01-22 03:08:26 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Jon Elson 2003-01-22 09:34:43 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Tim Goldstein 2003-01-22 09:54:03 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... alex 2003-01-22 10:13:54 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... j.guenther 2003-01-22 10:35:26 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Art 2003-01-22 13:50:45 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... j.guenther 2003-01-22 14:07:56 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Dan Statman 2003-01-22 14:34:36 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Art 2003-01-22 15:50:20 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Art 2003-01-22 15:58:39 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Bob Simon 2003-01-22 16:53:36 UTC RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... Art 2003-01-22 16:59:15 UTC Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions... ballendo <ballendo@y... 2003-01-23 01:55:26 UTC Re: EMC, ISA and other Questions... ballendo <ballendo@y... 2003-01-23 02:28:13 UTC EMC DOS source code was Re: EMC, ISA and other Questions... ballendo <ballendo@y... 2003-01-23 02:45:59 UTC Re: EMC, ISA and other Questions... ballendo <ballendo@y... 2003-01-23 02:55:25 UTC Of interpreters and controllers was Re: EMC, ISA and other Questions... ballendo <ballendo@y... 2003-01-23 04:16:19 UTC ABC axis stuff was Re: EMC, ISA and other Questions... rainnea <rainnea@b... 2003-01-23 06:21:31 UTC Re: EMC, ISA and other Questions... - 4th axis angular feedrates IMService 2003-01-23 07:30:53 UTC Re: RE: EMC, ISA and other Questions... torsten98001 <torsten@g... 2003-01-23 13:00:20 UTC ABC axis stuff was Re: EMC, ISA and other Questions... Matt Shaver 2003-01-23 23:12:56 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions... Art 2003-01-24 13:06:55 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions... Ray Henry 2003-01-25 13:33:18 UTC Re: Re: Re: EMC, ISA and other Questions... alex 2003-03-11 15:23:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions... Paul 2003-03-11 15:40:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions... alex 2003-03-11 15:52:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions... Jon Elson 2003-03-11 22:25:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions... Ray Henry 2003-03-12 06:41:41 UTC Re: Re: Re: Re: EMC, ISA and other Questions... alex 2003-03-12 07:51:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions... alex 2003-03-12 08:20:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Re: EMC, ISA and other Questions... alex 2003-03-12 14:56:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions... Paul 2003-03-12 15:20:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions... alex 2003-03-12 15:25:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...