RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
Posted by
Carol & Jerry Jankura
on 2003-01-21 05:53:07 UTC
Hi, Ivan:
If you're going to run the EMC (or any other) G-Code controller under
windows, you'll have to use either an external pulse generator or design a
software driver to allow real-time control of the printer port. While it's
easy to build a really neat looking interface under windows, there's enough
internal overhead in that operating environment to make it difficult to send
a robust pulse train out of the printer port.
That being said, Art Fenerty appears to have figured out how to write those
drivers for his Master5 and Mach1 G-Code controllers. I use the word
'appears' because I have not tried his software and have no first-hand
experience. I believe that his controllers are at least based on the EMC
definition and may have started with the EMC source code.
In any event, good luck on your endeavor. You might also want to take a look
at the G2002 board set from Gecko for use as your external pulse generator.
-- Jerry
If you're going to run the EMC (or any other) G-Code controller under
windows, you'll have to use either an external pulse generator or design a
software driver to allow real-time control of the printer port. While it's
easy to build a really neat looking interface under windows, there's enough
internal overhead in that operating environment to make it difficult to send
a robust pulse train out of the printer port.
That being said, Art Fenerty appears to have figured out how to write those
drivers for his Master5 and Mach1 G-Code controllers. I use the word
'appears' because I have not tried his software and have no first-hand
experience. I believe that his controllers are at least based on the EMC
definition and may have started with the EMC source code.
In any event, good luck on your endeavor. You might also want to take a look
at the G2002 board set from Gecko for use as your external pulse generator.
-- Jerry
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "zestronad54529
> <dpeter@n...>" <dpeter@n...> wrote:
> > I haven't gone hacking into EMC yet, but has anyone tried to
> port
> > it to windows? I normally work in VB and VC++ and as of yet not
> > played in Linux and haven't even seen a Unix box in 15 years.
>
> Perhaps a little OT, but you may want to look at Unix/Linux again. I
> worked with a NICE Unix box in Eng Dept at last shop I was at. You
> can choose GUI, text, or use both in different windows -- and crash
> in one application doesn't stop everything else. I'm trying to get a
> box around to load an old version of RedHat (never could get a
> separate machine around for it before), so I really can't tell you
> about Linux yet.
>
Discussion Thread
zestronad54529 <dpeter@n...
2003-01-20 20:15:27 UTC
EMC, ISA and other Questions...
Ivan Nichols <ouisel@v...
2003-01-21 05:12:00 UTC
Re: EMC, ISA and other Questions...
Dave Lantz
2003-01-21 05:17:38 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
Carol & Jerry Jankura
2003-01-21 05:53:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
Vince Negrete
2003-01-21 07:44:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
alex
2003-01-21 07:50:53 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
j.guenther
2003-01-21 08:15:56 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
alex
2003-01-21 08:23:48 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Vince Negrete
2003-01-21 08:27:57 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
j.guenther
2003-01-21 08:36:48 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
alex
2003-01-21 08:50:25 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Vince Negrete
2003-01-21 08:54:20 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
j.guenther
2003-01-21 09:03:23 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Tim Goldstein
2003-01-21 09:14:34 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
j.guenther
2003-01-21 09:18:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
alex
2003-01-21 09:18:44 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Jon Elson
2003-01-21 09:21:18 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Jon Elson
2003-01-21 09:28:01 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
j.guenther
2003-01-21 09:39:00 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
alex
2003-01-21 09:52:47 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Carol & Jerry Jankura
2003-01-21 10:44:26 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Carol & Jerry Jankura
2003-01-21 10:44:30 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
alex
2003-01-21 11:12:33 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Ray Henry
2003-01-21 13:44:43 UTC
Re: EMC, ISA and other Questions...
jmkasunich <jmkasunich@y...
2003-01-21 14:53:28 UTC
PLEASE TRIM POSTS!! was Re: EMC, ISA and other Questions...
Ray Henry
2003-01-21 17:10:00 UTC
Re: Re: EMC, ISA and other Questions...
Ray Henry
2003-01-21 17:10:03 UTC
Re: Re: EMC, ISA and other Questions...
Jon Elson
2003-01-21 23:16:20 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Jon Elson
2003-01-21 23:18:01 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Tim Goldstein
2003-01-21 23:27:54 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Matt Shaver
2003-01-22 03:08:26 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Jon Elson
2003-01-22 09:34:43 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Tim Goldstein
2003-01-22 09:54:03 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
alex
2003-01-22 10:13:54 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
j.guenther
2003-01-22 10:35:26 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Art
2003-01-22 13:50:45 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
j.guenther
2003-01-22 14:07:56 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Dan Statman
2003-01-22 14:34:36 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Art
2003-01-22 15:50:20 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Art
2003-01-22 15:58:39 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Bob Simon
2003-01-22 16:53:36 UTC
RE: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
Art
2003-01-22 16:59:15 UTC
Re: [CAD_CAM_EDM_DRO] EMC, ISA and other Questions...
ballendo <ballendo@y...
2003-01-23 01:55:26 UTC
Re: EMC, ISA and other Questions...
ballendo <ballendo@y...
2003-01-23 02:28:13 UTC
EMC DOS source code was Re: EMC, ISA and other Questions...
ballendo <ballendo@y...
2003-01-23 02:45:59 UTC
Re: EMC, ISA and other Questions...
ballendo <ballendo@y...
2003-01-23 02:55:25 UTC
Of interpreters and controllers was Re: EMC, ISA and other Questions...
ballendo <ballendo@y...
2003-01-23 04:16:19 UTC
ABC axis stuff was Re: EMC, ISA and other Questions...
rainnea <rainnea@b...
2003-01-23 06:21:31 UTC
Re: EMC, ISA and other Questions... - 4th axis angular feedrates
IMService
2003-01-23 07:30:53 UTC
Re: RE: EMC, ISA and other Questions...
torsten98001 <torsten@g...
2003-01-23 13:00:20 UTC
ABC axis stuff was Re: EMC, ISA and other Questions...
Matt Shaver
2003-01-23 23:12:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
Art
2003-01-24 13:06:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC, ISA and other Questions...
Ray Henry
2003-01-25 13:33:18 UTC
Re: Re: Re: EMC, ISA and other Questions...
alex
2003-03-11 15:23:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...
Paul
2003-03-11 15:40:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...
alex
2003-03-11 15:52:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...
Jon Elson
2003-03-11 22:25:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...
Ray Henry
2003-03-12 06:41:41 UTC
Re: Re: Re: Re: EMC, ISA and other Questions...
alex
2003-03-12 07:51:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...
alex
2003-03-12 08:20:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Re: EMC, ISA and other Questions...
alex
2003-03-12 14:56:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...
Paul
2003-03-12 15:20:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...
alex
2003-03-12 15:25:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: EMC, ISA and other Questions...