Phase converter questions
Posted by
jlsmith269
on 2004-01-17 09:31:30 UTC
Okay, on a 1 phase to 3 phase converter
1: I hear that the statics have a maximum number of on/off cycles per
hour. If this is no longer true, please post MODEL and MAKE for me to
aquire one
2: Rotory was/is the way to go, but I hear that's not longer the
preferred method
3: VFD ? ? are the best way to go for static?
I'll tell you the truth, I am leaning towards a 5hp rotary to run a 2
hp 220/p3 mill.. Planning on buying a kit for the tronics off ebay and
then aquirring a 5 hp motor local
Thoughts? suggestions?
1: I hear that the statics have a maximum number of on/off cycles per
hour. If this is no longer true, please post MODEL and MAKE for me to
aquire one
2: Rotory was/is the way to go, but I hear that's not longer the
preferred method
3: VFD ? ? are the best way to go for static?
I'll tell you the truth, I am leaning towards a 5hp rotary to run a 2
hp 220/p3 mill.. Planning on buying a kit for the tronics off ebay and
then aquirring a 5 hp motor local
Thoughts? suggestions?
Discussion Thread
jlsmith269
2004-01-17 09:31:30 UTC
Phase converter questions
rawen2
2004-01-17 10:49:32 UTC
Re: Phase converter questions
Peter Renolds
2004-01-17 11:18:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Bob McKnight
2004-01-17 12:28:54 UTC
Re: [CAD_CAM_EDM_DRO] Phase converter questions
Jon Elson
2004-01-17 20:26:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Lee Studley
2004-01-18 04:09:35 UTC
Re: Phase converter questions
Robin Szemeti
2004-01-18 04:48:56 UTC
Re: [CAD_CAM_EDM_DRO] Phase converter questions
jlsmith269
2004-01-18 07:17:28 UTC
Re: Phase converter questions
johnatjandj
2004-01-18 07:27:59 UTC
Re: Phase converter questions
Peter Renolds
2004-01-18 07:57:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
jlsmith269
2004-01-18 10:22:23 UTC
Re: Phase converter questions
Robin Szemeti
2004-01-18 11:33:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Scot
2004-01-18 12:01:28 UTC
Re: Phase converter questions
doug98105
2004-01-18 14:33:38 UTC
Re: Phase converter questions
Bob McKnight
2004-01-18 14:59:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Garage door openers
Shawncd
2004-01-18 16:52:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Shawncd
2004-01-18 16:54:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Garage door openers
Bill P @ ...
2004-01-18 17:28:52 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Phase Converter Noise
Jon Elson
2004-01-18 20:28:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Raymond Heckert
2004-01-19 16:14:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions