Re: [CAD_CAM_EDM_DRO] Phase converter questions
Posted by
Robin Szemeti
on 2004-01-18 04:48:56 UTC
On Saturday 17 January 2004 20:31, Bob McKnight wrote:
and enjoy. For driving motors up to 5hp or so from single pahse, VFD's are
without a doubt the way to go. Your comments above seem to suggest you were
thinking of some weird combination of VFD and static convertor or somehting
.. totally unecessary, just wire the VFD to the motor on the mill (having
checked the voltages) and you're done.
The big problem with rotary convertors is finding the correct belts for
hooking them up to the steam engine, and static converotrs are getting more
difficult to run these days because its hard to find the right sort of coal.
--
Redpoint Consulting Limited
Real Solutions for a Virtual World
http://www.redpoint.org.uk
> 3: VFD ? ? are the best way to go for static?just buy a 2 or 3hp single to 3 phase VFD, wire it to the motor on your mill
>
> I'll tell you the truth, I am leaning towards a 5hp rotary to run a 2
> hp 220/p3 mill.. Planning on buying a kit for the tronics off ebay and
> then aquirring a 5 hp motor local
and enjoy. For driving motors up to 5hp or so from single pahse, VFD's are
without a doubt the way to go. Your comments above seem to suggest you were
thinking of some weird combination of VFD and static convertor or somehting
.. totally unecessary, just wire the VFD to the motor on the mill (having
checked the voltages) and you're done.
The big problem with rotary convertors is finding the correct belts for
hooking them up to the steam engine, and static converotrs are getting more
difficult to run these days because its hard to find the right sort of coal.
--
Redpoint Consulting Limited
Real Solutions for a Virtual World
http://www.redpoint.org.uk
Discussion Thread
jlsmith269
2004-01-17 09:31:30 UTC
Phase converter questions
rawen2
2004-01-17 10:49:32 UTC
Re: Phase converter questions
Peter Renolds
2004-01-17 11:18:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Bob McKnight
2004-01-17 12:28:54 UTC
Re: [CAD_CAM_EDM_DRO] Phase converter questions
Jon Elson
2004-01-17 20:26:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Lee Studley
2004-01-18 04:09:35 UTC
Re: Phase converter questions
Robin Szemeti
2004-01-18 04:48:56 UTC
Re: [CAD_CAM_EDM_DRO] Phase converter questions
jlsmith269
2004-01-18 07:17:28 UTC
Re: Phase converter questions
johnatjandj
2004-01-18 07:27:59 UTC
Re: Phase converter questions
Peter Renolds
2004-01-18 07:57:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
jlsmith269
2004-01-18 10:22:23 UTC
Re: Phase converter questions
Robin Szemeti
2004-01-18 11:33:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Scot
2004-01-18 12:01:28 UTC
Re: Phase converter questions
doug98105
2004-01-18 14:33:38 UTC
Re: Phase converter questions
Bob McKnight
2004-01-18 14:59:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Garage door openers
Shawncd
2004-01-18 16:52:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Shawncd
2004-01-18 16:54:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Garage door openers
Bill P @ ...
2004-01-18 17:28:52 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Phase Converter Noise
Jon Elson
2004-01-18 20:28:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Raymond Heckert
2004-01-19 16:14:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions