CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Garage door openers

Posted by Shawncd
on 2004-01-18 16:54:59 UTC
Anthing is possible. Accuracy will be a problem with acme thread. If your
not holding tight tolerances should work fine.


----- Original Message -----
From: "Bob McKnight" <bobmcknight@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Sunday, January 18, 2004 3:02 PM
Subject: Re: [CAD_CAM_EDM_DRO] Re: Garage door openers


> has anybody used a garage door opener to drive an axis?
>
> I would like to make a big cutting table. I have quite a few
> garage door openers. One is a Genie that has a half inch
> acme (?) thread, 8 turns to the inch, It is 8 feet long in a nice
> aluminum extrusion for support. For a plasma cutter, it looks
> like it could drive the gantry from a center overhead position.
> The z axis doesn't seem to need much travel for a cutter. There
> would be no cutting pressure on the gantry.
>
> Bob McKnight
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Yahoo! Groups Links
>
> To visit your group on the web, go to:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/
>
> To unsubscribe from this group, send an email to:
> CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>
> Your use of Yahoo! Groups is subject to:
> http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

jlsmith269 2004-01-17 09:31:30 UTC Phase converter questions rawen2 2004-01-17 10:49:32 UTC Re: Phase converter questions Peter Renolds 2004-01-17 11:18:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions Bob McKnight 2004-01-17 12:28:54 UTC Re: [CAD_CAM_EDM_DRO] Phase converter questions Jon Elson 2004-01-17 20:26:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions Lee Studley 2004-01-18 04:09:35 UTC Re: Phase converter questions Robin Szemeti 2004-01-18 04:48:56 UTC Re: [CAD_CAM_EDM_DRO] Phase converter questions jlsmith269 2004-01-18 07:17:28 UTC Re: Phase converter questions johnatjandj 2004-01-18 07:27:59 UTC Re: Phase converter questions Peter Renolds 2004-01-18 07:57:56 UTC Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions jlsmith269 2004-01-18 10:22:23 UTC Re: Phase converter questions Robin Szemeti 2004-01-18 11:33:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions Scot 2004-01-18 12:01:28 UTC Re: Phase converter questions doug98105 2004-01-18 14:33:38 UTC Re: Phase converter questions Bob McKnight 2004-01-18 14:59:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Garage door openers Shawncd 2004-01-18 16:52:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions Shawncd 2004-01-18 16:54:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Garage door openers Bill P @ ... 2004-01-18 17:28:52 UTC Re: [CAD_CAM_EDM_DRO] Rotary Phase Converter Noise Jon Elson 2004-01-18 20:28:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions Raymond Heckert 2004-01-19 16:14:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions