Re: Phase converter questions
Posted by
johnatjandj
on 2004-01-18 07:27:59 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "jlsmith269"
<jlsmith269@y...> wrote:
If you want to build a rotary phase converter just do a google search
for phase converter and George Carlson he has an great page on this.
If you want the VFD way check out automationdirect.com or e-bay. be
warned some older VFD's choke on single phase inputs. I have a 3 hp
rotary running a 2hp mill. It runs good on low speed (2 speed motor)
but will not run it in high speed. my 5hp will run it in both speeds
with out any problem. Make sure you balance the voltage on your three
legs of the three phase.
JOhn
<jlsmith269@y...> wrote:
If you want to build a rotary phase converter just do a google search
for phase converter and George Carlson he has an great page on this.
If you want the VFD way check out automationdirect.com or e-bay. be
warned some older VFD's choke on single phase inputs. I have a 3 hp
rotary running a 2hp mill. It runs good on low speed (2 speed motor)
but will not run it in high speed. my 5hp will run it in both speeds
with out any problem. Make sure you balance the voltage on your three
legs of the three phase.
JOhn
> Okay, on a 1 phase to 3 phase converterper
>
> 1: I hear that the statics have a maximum number of on/off cycles
> hour. If this is no longer true, please post MODEL and MAKE for meto
> aquire one2
>
> 2: Rotory was/is the way to go, but I hear that's not longer the
> preferred method
>
> 3: VFD ? ? are the best way to go for static?
>
> I'll tell you the truth, I am leaning towards a 5hp rotary to run a
> hp 220/p3 mill.. Planning on buying a kit for the tronics off ebayand
> then aquirring a 5 hp motor local
>
>
> Thoughts? suggestions?
Discussion Thread
jlsmith269
2004-01-17 09:31:30 UTC
Phase converter questions
rawen2
2004-01-17 10:49:32 UTC
Re: Phase converter questions
Peter Renolds
2004-01-17 11:18:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Bob McKnight
2004-01-17 12:28:54 UTC
Re: [CAD_CAM_EDM_DRO] Phase converter questions
Jon Elson
2004-01-17 20:26:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Lee Studley
2004-01-18 04:09:35 UTC
Re: Phase converter questions
Robin Szemeti
2004-01-18 04:48:56 UTC
Re: [CAD_CAM_EDM_DRO] Phase converter questions
jlsmith269
2004-01-18 07:17:28 UTC
Re: Phase converter questions
johnatjandj
2004-01-18 07:27:59 UTC
Re: Phase converter questions
Peter Renolds
2004-01-18 07:57:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
jlsmith269
2004-01-18 10:22:23 UTC
Re: Phase converter questions
Robin Szemeti
2004-01-18 11:33:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Scot
2004-01-18 12:01:28 UTC
Re: Phase converter questions
doug98105
2004-01-18 14:33:38 UTC
Re: Phase converter questions
Bob McKnight
2004-01-18 14:59:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Garage door openers
Shawncd
2004-01-18 16:52:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Shawncd
2004-01-18 16:54:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Garage door openers
Bill P @ ...
2004-01-18 17:28:52 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Phase Converter Noise
Jon Elson
2004-01-18 20:28:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions
Raymond Heckert
2004-01-19 16:14:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Phase converter questions