Re: BP retrofit yaxis drive burnup- follow-up
Posted by
ajv2803959
on 2005-04-08 04:02:16 UTC
Keith could you post an wiring schematic of your new system ?
I am cabling my driver box and would like minimize the early problems
thay you had.
Thanks ind Advance
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Keith Clark" <mail@t...>
wrote:
I am cabling my driver box and would like minimize the early problems
thay you had.
Thanks ind Advance
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Keith Clark" <mail@t...>
wrote:
>
> I'd like to give some follow-up on the complete reworking of my BP
> retrofit. I was burning up Geckos on the y axis. The installer
> originally put in everything on top of all the original BP CNC
> equipment. I gutted the cabinets and rewired everything. Just tried
> out the machine and everything works almost. The relay for the DC
> powersupply that had been on the DC side got switched to the AC
> side. With switching on the DC side there was always a "bump" of
> the motors and the backup powersupply for the computer sensed a
> spike and briefly shutdown. Now with the AC side switched there is
> no bump. Hopefully the electrical problems are behind me except for
> the fact that the x axis will not run smoothly. It stalls unless
> tuned for very slow speed. The y and z axes run at top speed and
> acceleration in Mach2, much better than before. It looks like the
> wires are all connected properly but I will recheck everything
> tomorrow. In the old configuration the x axis always ran fine.
>
> If the wiring is fine and the capacitor across the power on the
> Geckos is not bad, what next?
>
> Thanks for any suggestions.
>
> Keith Clark
Discussion Thread
Keith Clark
2005-04-07 23:31:03 UTC
BP retrofit yaxis drive burnup- follow-up
ajv2803959
2005-04-08 04:02:16 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Keith Clark
2005-04-08 05:28:08 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Ron Kline
2005-04-08 07:44:14 UTC
Re: [CAD_CAM_EDM_DRO] BP retrofit yaxis drive burnup- follow-up
Keith Clark
2005-04-08 12:38:06 UTC
Re: BP retrofit yaxis drive burnup- follow-up
lcdpublishing
2005-04-08 14:10:19 UTC
Gecko problems - What is going on?
Keith Clark
2005-04-08 14:24:44 UTC
Re: Gecko problems - What is going on?
Pete Brown (YahooGroups)
2005-04-08 14:27:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko problems - What is going on?
Keith Clark
2005-04-08 14:32:03 UTC
Re: Gecko problems - What is going on?
Ron Kline
2005-04-08 15:00:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
Les Newell
2005-04-08 15:24:54 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Les Newell
2005-04-08 15:36:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko problems - What is going on?
Jeff Goldberg
2005-04-08 16:33:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
R Rogers
2005-04-08 19:28:29 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Ron Kline
2005-04-08 20:12:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
George Taylor, IV
2005-04-08 20:24:40 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Ron Kline
2005-04-08 20:38:19 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
R Rogers
2005-04-08 21:01:00 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Keith Clark
2005-04-08 21:09:15 UTC
Re: Gecko problems - What is going on? New finding
Jon Elson
2005-04-08 21:26:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
Jon Elson
2005-04-08 21:32:46 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
cnc_4_me
2005-04-09 08:02:45 UTC
Re: BP retrofit yaxis drive burnup- follow-up
George Taylor, IV
2005-04-09 11:20:24 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Keith Clark
2005-04-09 11:46:34 UTC
Re: BP retrofit yaxis drive burnup- follow-up FIXED!
JCullins
2005-04-09 12:04:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up FIXED!
Ron Kline
2005-04-09 12:41:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up FIXED!
Ron Kline
2005-04-09 12:47:20 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
R Rogers
2005-04-09 13:25:54 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Jon Elson
2005-04-09 14:03:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
cnc_4_me
2005-04-09 15:10:43 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Keith Clark
2005-04-09 16:47:59 UTC
Re: BP retrofit yaxis drive burnup- follow-up
George Taylor, IV
2005-04-09 18:59:30 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
George Taylor, IV
2005-04-09 19:01:45 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
George Taylor, IV
2005-04-09 19:09:55 UTC
RE: Your machine
Jon Elson
2005-04-09 21:16:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
Jon Elson
2005-04-09 21:22:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
cnc_4_me
2005-04-09 22:21:48 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Jon Elson
2005-04-10 11:50:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up