CAD CAM EDM DRO - Yahoo Group Archive

Re: BP retrofit yaxis drive burnup- follow-up

Posted by cnc_4_me
on 2005-04-09 22:21:48 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
> it is a pretty general device. It has a 56 A MOSFET transistor,
and an
> charge pump circuit that gradually charges a capacitor, ramping the
> voltage to the motor drives up at a steady rate.


What is its working voltage and current range.

Wally




--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
> Keith Clark wrote:
>
> >Jon,
> >
> >Can you enlighten us about the ramp-up module? This might
certainly
> >help me avoid more damage to the Geckos during estop now that I
have
> >a fully functional machine.
> >
> >
> Sure, see http://jelinux.pico-systems.com/pwmsw.html
>
> This was designed for my PWM servo amplifiers and PWM controller,
but
> it is a pretty general device. It has a 56 A MOSFET transistor,
and an
> charge pump circuit that gradually charges a capacitor, ramping the
> voltage to the motor drives up at a steady rate. When the power on
signal
> is turned off, it activates a braking resistor that removes all
energy from
> possibly still spinning motors.
>
> It has 3 power connections : Gnd, DC power in and DC power out.
> It has one control signal, Power On NOT. IE. this signal is
grounded
> to power the drives on. It requires 5 V DC from some external
source.
> The Power On NOT signal is not opto-isolated.
>
> Jon

Discussion Thread

Keith Clark 2005-04-07 23:31:03 UTC BP retrofit yaxis drive burnup- follow-up ajv2803959 2005-04-08 04:02:16 UTC Re: BP retrofit yaxis drive burnup- follow-up Keith Clark 2005-04-08 05:28:08 UTC Re: BP retrofit yaxis drive burnup- follow-up Ron Kline 2005-04-08 07:44:14 UTC Re: [CAD_CAM_EDM_DRO] BP retrofit yaxis drive burnup- follow-up Keith Clark 2005-04-08 12:38:06 UTC Re: BP retrofit yaxis drive burnup- follow-up lcdpublishing 2005-04-08 14:10:19 UTC Gecko problems - What is going on? Keith Clark 2005-04-08 14:24:44 UTC Re: Gecko problems - What is going on? Pete Brown (YahooGroups) 2005-04-08 14:27:02 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko problems - What is going on? Keith Clark 2005-04-08 14:32:03 UTC Re: Gecko problems - What is going on? Ron Kline 2005-04-08 15:00:47 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up Les Newell 2005-04-08 15:24:54 UTC Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? Les Newell 2005-04-08 15:36:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko problems - What is going on? Jeff Goldberg 2005-04-08 16:33:26 UTC RE: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up R Rogers 2005-04-08 19:28:29 UTC Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? Ron Kline 2005-04-08 20:12:02 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up George Taylor, IV 2005-04-08 20:24:40 UTC RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? Ron Kline 2005-04-08 20:38:19 UTC Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? R Rogers 2005-04-08 21:01:00 UTC RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? Keith Clark 2005-04-08 21:09:15 UTC Re: Gecko problems - What is going on? New finding Jon Elson 2005-04-08 21:26:06 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up Jon Elson 2005-04-08 21:32:46 UTC Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? cnc_4_me 2005-04-09 08:02:45 UTC Re: BP retrofit yaxis drive burnup- follow-up George Taylor, IV 2005-04-09 11:20:24 UTC RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? Keith Clark 2005-04-09 11:46:34 UTC Re: BP retrofit yaxis drive burnup- follow-up FIXED! JCullins 2005-04-09 12:04:59 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up FIXED! Ron Kline 2005-04-09 12:41:24 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up FIXED! Ron Kline 2005-04-09 12:47:20 UTC Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? R Rogers 2005-04-09 13:25:54 UTC RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? Jon Elson 2005-04-09 14:03:30 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up cnc_4_me 2005-04-09 15:10:43 UTC Re: BP retrofit yaxis drive burnup- follow-up Keith Clark 2005-04-09 16:47:59 UTC Re: BP retrofit yaxis drive burnup- follow-up George Taylor, IV 2005-04-09 18:59:30 UTC RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? George Taylor, IV 2005-04-09 19:01:45 UTC RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on? George Taylor, IV 2005-04-09 19:09:55 UTC RE: Your machine Jon Elson 2005-04-09 21:16:24 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up Jon Elson 2005-04-09 21:22:49 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up cnc_4_me 2005-04-09 22:21:48 UTC Re: BP retrofit yaxis drive burnup- follow-up Jon Elson 2005-04-10 11:50:13 UTC Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up