Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
Posted by
Jon Elson
on 2005-04-09 21:22:49 UTC
Keith Clark wrote:
This was designed for my PWM servo amplifiers and PWM controller, but
it is a pretty general device. It has a 56 A MOSFET transistor, and an
charge pump circuit that gradually charges a capacitor, ramping the
voltage to the motor drives up at a steady rate. When the power on signal
is turned off, it activates a braking resistor that removes all energy from
possibly still spinning motors.
It has 3 power connections : Gnd, DC power in and DC power out.
It has one control signal, Power On NOT. IE. this signal is grounded
to power the drives on. It requires 5 V DC from some external source.
The Power On NOT signal is not opto-isolated.
Jon
>Jon,Sure, see http://jelinux.pico-systems.com/pwmsw.html
>
>Can you enlighten us about the ramp-up module? This might certainly
>help me avoid more damage to the Geckos during estop now that I have
>a fully functional machine.
>
>
This was designed for my PWM servo amplifiers and PWM controller, but
it is a pretty general device. It has a 56 A MOSFET transistor, and an
charge pump circuit that gradually charges a capacitor, ramping the
voltage to the motor drives up at a steady rate. When the power on signal
is turned off, it activates a braking resistor that removes all energy from
possibly still spinning motors.
It has 3 power connections : Gnd, DC power in and DC power out.
It has one control signal, Power On NOT. IE. this signal is grounded
to power the drives on. It requires 5 V DC from some external source.
The Power On NOT signal is not opto-isolated.
Jon
Discussion Thread
Keith Clark
2005-04-07 23:31:03 UTC
BP retrofit yaxis drive burnup- follow-up
ajv2803959
2005-04-08 04:02:16 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Keith Clark
2005-04-08 05:28:08 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Ron Kline
2005-04-08 07:44:14 UTC
Re: [CAD_CAM_EDM_DRO] BP retrofit yaxis drive burnup- follow-up
Keith Clark
2005-04-08 12:38:06 UTC
Re: BP retrofit yaxis drive burnup- follow-up
lcdpublishing
2005-04-08 14:10:19 UTC
Gecko problems - What is going on?
Keith Clark
2005-04-08 14:24:44 UTC
Re: Gecko problems - What is going on?
Pete Brown (YahooGroups)
2005-04-08 14:27:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko problems - What is going on?
Keith Clark
2005-04-08 14:32:03 UTC
Re: Gecko problems - What is going on?
Ron Kline
2005-04-08 15:00:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
Les Newell
2005-04-08 15:24:54 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Les Newell
2005-04-08 15:36:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko problems - What is going on?
Jeff Goldberg
2005-04-08 16:33:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
R Rogers
2005-04-08 19:28:29 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Ron Kline
2005-04-08 20:12:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
George Taylor, IV
2005-04-08 20:24:40 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Ron Kline
2005-04-08 20:38:19 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
R Rogers
2005-04-08 21:01:00 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Keith Clark
2005-04-08 21:09:15 UTC
Re: Gecko problems - What is going on? New finding
Jon Elson
2005-04-08 21:26:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
Jon Elson
2005-04-08 21:32:46 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
cnc_4_me
2005-04-09 08:02:45 UTC
Re: BP retrofit yaxis drive burnup- follow-up
George Taylor, IV
2005-04-09 11:20:24 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Keith Clark
2005-04-09 11:46:34 UTC
Re: BP retrofit yaxis drive burnup- follow-up FIXED!
JCullins
2005-04-09 12:04:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up FIXED!
Ron Kline
2005-04-09 12:41:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up FIXED!
Ron Kline
2005-04-09 12:47:20 UTC
Re: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
R Rogers
2005-04-09 13:25:54 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
Jon Elson
2005-04-09 14:03:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
cnc_4_me
2005-04-09 15:10:43 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Keith Clark
2005-04-09 16:47:59 UTC
Re: BP retrofit yaxis drive burnup- follow-up
George Taylor, IV
2005-04-09 18:59:30 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
George Taylor, IV
2005-04-09 19:01:45 UTC
RE: [CAD_CAM_EDM_DRO] Gecko problems - What is going on?
George Taylor, IV
2005-04-09 19:09:55 UTC
RE: Your machine
Jon Elson
2005-04-09 21:16:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
Jon Elson
2005-04-09 21:22:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up
cnc_4_me
2005-04-09 22:21:48 UTC
Re: BP retrofit yaxis drive burnup- follow-up
Jon Elson
2005-04-10 11:50:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: BP retrofit yaxis drive burnup- follow-up