RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Posted by
Alan Marconett
on 2005-09-29 13:59:11 UTC
HI Victor,
Thanks for the description! You've whetted my appetite! I did a little
experimenting with a pen, I put in a Rapidograph pen.
Alan KM6VV
Thanks for the description! You've whetted my appetite! I did a little
experimenting with a pen, I put in a Rapidograph pen.
Alan KM6VV
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Victor A. Estes
> Sent: Thursday, September 29, 2005 1:49 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
>
> Alan,
>
> Yea the pin I used was dried up as well. I pulled the tip out with a
> pair of pliers, then I used a small rod to push up through the hole to pop
> the end cap off. I then pulled out the felt core and through away. That
> left me with a very nice plastic housing that I could use as the holder.
> I
> turned a piece of aluminum to fit inside the plastic housing and turned
> the
> aluminum housing to fit the bearing that I had ordered from McMaster Carr.
> I then bored out a small recess for the magnet, superglued the mag in
> place,
> and pressed in the bearing. On the other end I had drilled all the way
> through, so I could knock the mag and bearing out if I needed to. I also
> tapped the hole for a 4-40 thread so that I could secure the aluminum
> holder
> into the plastic housing. On the plastic housing, I cut off the tapered
> end, and made that the top. The end where the plastic cap was fitted now
> became the bottom, and the aluminum holder slides in from this end. The
> 4-40 screw screws in from the other end and keeps everything sandwiched
> together. The I inserted the blade into the bearing hole and viola. It
> works. The holder still fits in the pin holder on the carriage, just
> upside
> down from the original. The knife blade pivots on the magnet and bearing
> with no friction at all. Pics to follow next week.
>
> Victor
> ----- Original Message -----
> From: "Alan Marconett" <KM6VV@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Thursday, September 29, 2005 12:09 PM
> Subject: RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
>
>
Discussion Thread
Victor A. Estes
2005-09-28 15:07:11 UTC
Hp 7475 Plotter Servo's
Alan Marconett
2005-09-28 16:07:37 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
caedave
2005-09-28 16:39:50 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Blue
2005-09-28 17:21:20 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
KM6VV
2005-09-28 17:42:19 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
jerry stout
2005-09-29 06:19:02 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 06:22:39 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:26:13 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:27:03 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:36:28 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 06:39:20 UTC
Re: Hp 7475 Plotter Servo's - Drag knife
turbulatordude
2005-09-29 06:41:22 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:44:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:56:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's - Drag knife
Blue
2005-09-29 06:57:26 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 07:03:15 UTC
Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:24:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:27:34 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:36:10 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 08:40:50 UTC
Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:46:36 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:51:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 08:57:09 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 09:31:46 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 09:42:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Hugh Prescott
2005-09-29 09:59:47 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Randy Gordon-Gilmore
2005-09-29 10:10:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Hugh Prescott
2005-09-29 10:12:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 10:15:50 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 10:20:41 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 10:50:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 13:49:14 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 13:59:11 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
George Taylor, IV
2005-09-29 14:47:37 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Tom Harrison
2005-09-29 15:40:38 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
caedave
2005-09-30 04:01:38 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Raymond Heckert
2005-09-30 19:49:59 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-02 11:47:41 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-10-02 13:15:26 UTC
Re: Hp 7475 Plotter Servo's
caedave
2005-10-03 05:06:06 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-03 08:00:58 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-10-03 11:06:16 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-04 07:11:07 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Stephen Wille Padnos
2005-10-04 07:33:42 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Jymmm
2005-10-04 09:36:44 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-04 11:14:20 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-04 14:42:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-20 09:33:45 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Russ Waters
2005-10-20 09:51:47 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
wbhinkle@a...
2005-10-20 10:01:24 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Hugh Prescott
2005-10-20 10:22:17 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-10-20 10:35:37 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's, 3D surface modeling for EGG-BOT
Victor A. Estes
2005-10-20 10:40:18 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Roy J. Tellason
2005-10-20 10:41:43 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
wbhinkle@a...
2005-10-20 10:44:18 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-20 11:22:37 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's, 3D surface modeling for EGG-BOT
emc3zach
2005-10-20 14:29:58 UTC
Re: Hp 7475 Plotter Servo's
Roy J. Tellason
2005-10-20 15:58:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-21 06:17:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's