Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Posted by
Victor A. Estes
on 2005-10-03 08:00:58 UTC
Thanks Dave M, I'll break out the meter and scope. Already made a cable
with the correct pin outs and crossovers and still does not work. In fact
that was the first thing I did, before I spent the money on a new cable. I
have not checked the plug at the plotter. Will try that as well.
Sincerely,
Victor A. Estes
with the correct pin outs and crossovers and still does not work. In fact
that was the first thing I did, before I spent the money on a new cable. I
have not checked the plug at the plotter. Will try that as well.
Sincerely,
Victor A. Estes
----- Original Message -----
From: "caedave" <caedave@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, October 03, 2005 7:04 AM
Subject: Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
> You can't as such, it's a case of find the fault, correct it and
> the error goes away.
>
> Unfortunately I/O errors can be a nightmare to fix.
>
> Turbo's (the other Dave) message has some pointers but
> start out by checking the pin outs and Dip settings, if they
> are correct then it's time to get the meter and scope out
> so you can check continuity, pulse timings and levels.
>
> Try to also check these within the plotter so that you know
> the plugs are making good connections (been caught by this).
>
> Make up a plug with the correct crossover connections for
> the comms status. With this plugged into the plotter if you
> still get the error then at least you know the fault is something
> to do with the plotter.
>
> Dave M.
>
> ----- Original Message -----
> From: "Victor A. Estes" <emc3zach@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Sunday, October 02, 2005 7:47 PM
> Subject: Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
>
>
>> Dave,
>> Thanks, it's has to be the I/O error. Any idea how to reset a I/O error.
>>
>> Victor
>>
>>
>>>From: "caedave" <caedave@...>
>>>Reply-To: CAD_CAM_EDM_DRO@yahoogroups.com
>>>To: <CAD_CAM_EDM_DRO@yahoogroups.com>
>>>Subject: Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
>>>Date: Fri, 30 Sep 2005 12:01:18 +0100
>>>
>>>Took a look on HP's site (Not the best to navigate around) and
>>>did eventually find some info on the 7475's including full pin out
>>>listings, Dip switch positions, test procedures and setting up.
>>>
>>>Limited amount on the error codes (lights) listed below.
>>>
>>>1. Error light dim, slow blink :-
>>> Plotter not active but performing power management.
>>>
>>>2. Error light on steady :-
>>> View Button pressed or plotter in paper load mode
>>> (Pinch wheel lever Up)
>>>
>>>3. Error Light fast blink :-
>>> I/O error, Paper jamb error, HP-GL error.
>>> For these it then references certain sections of the manual.
>>>
>>>Dave M.
>>>
>>>----- Original Message -----
>>>From: "Tom Harrison" <TomH-CNC@...>
>>>Subject: Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
>>>
>>>
>>> > Don't forget: It also flips data receive and transmit (pins 2 and 3).
>>> >
>>> > Try this: using a digital voltmeter, measure the voltage at pins 2 and
>>> > 3
>>> > using pin 7 as a reference. The one with an active negative voltage
>>> > (between -5 and -15 volts) is the pin the device is using to send data
>>>out
>>> > to the world. On your plotter and on your computer (use a 9-pin to
>>>25-pin
>>> > convertor if necessary), they must be on different pins to
>>> > communicate.
>>> > Then apply jumpering if necessary, to satisfy the RTS/CTS and
>>>DSR/DTR/DCD
>>> > requirements of each end.
>>> >
>>> > Realize also that some interfaces actually USE the other control
>>> > signals
>>> > to
>>> > throttle data flow so as to not overwhelm buffers. Not all use the
>>> > character-based throttling, like XON/XOFF and the like.
>>> >
>>> > More details if you need....
>>> >
>>> > Tom Harrison
>>>
>>>
>>>
>>>--
>>>No virus found in this outgoing message.
>>>Checked by AVG Anti-Virus.
>>>Version: 7.0.344 / Virus Database: 267.11.9/115 - Release Date:
>>>29/09/2005
>>>
>>>
>>>
>>>Addresses:
>>>FAQ: http://www.ktmarketing.com/faq.html
>>>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>>>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>>
>>>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>>>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>>>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
>>>timg@...
>>>Moderator: pentam@... indigo_red@... davemucha@...
>>>[Moderators]
>>>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>>
>>>OFF Topic POSTS: General Machining
>>>If you wish to post on unlimited OT subjects goto:
>>>aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
>>>if
>>>you have trouble.
>>>http://www.metalworking.com/news_servers.html
>>>
>>>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
>>>sister site to the CCED group, as many of the same members are there, for
>>>OT subjects, that are not allowed on the CCED list.
>>>
>>>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
>>>DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>>>bill
>>>List Mom
>>>List Owner
>>>
>>>
>>>Yahoo! Groups Links
>>>
>>>
>>>
>>>
>>>
>>>
>>
>>
>>
>>
>> Addresses:
>> FAQ: http://www.ktmarketing.com/faq.html
>> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>
>> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
>> timg@...
>> Moderator: pentam@... indigo_red@... davemucha@...
>> [Moderators]
>> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>
>> OFF Topic POSTS: General Machining
>> If you wish to post on unlimited OT subjects goto:
>> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
>> if you have trouble.
>> http://www.metalworking.com/news_servers.html
>>
>> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
>> sister site to the CCED group, as many of the same members are there, for
>> OT subjects, that are not allowed on the CCED list.
>>
>> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
>> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>> bill
>> List Mom
>> List Owner
>>
>>
>> Yahoo! Groups Links
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> --
>> No virus found in this incoming message.
>> Checked by AVG Anti-Virus.
>> Version: 7.0.344 / Virus Database: 267.11.9/116 - Release Date:
>> 30/09/2005
>>
>>
>
>
>
> --
> No virus found in this outgoing message.
> Checked by AVG Anti-Virus.
> Version: 7.0.344 / Virus Database: 267.11.9/116 - Release Date: 30/09/2005
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
Discussion Thread
Victor A. Estes
2005-09-28 15:07:11 UTC
Hp 7475 Plotter Servo's
Alan Marconett
2005-09-28 16:07:37 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
caedave
2005-09-28 16:39:50 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Blue
2005-09-28 17:21:20 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
KM6VV
2005-09-28 17:42:19 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
jerry stout
2005-09-29 06:19:02 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 06:22:39 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:26:13 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:27:03 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:36:28 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 06:39:20 UTC
Re: Hp 7475 Plotter Servo's - Drag knife
turbulatordude
2005-09-29 06:41:22 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:44:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 06:56:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's - Drag knife
Blue
2005-09-29 06:57:26 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 07:03:15 UTC
Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:24:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:27:34 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:36:10 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 08:40:50 UTC
Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:46:36 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 08:51:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
turbulatordude
2005-09-29 08:57:09 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 09:31:46 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 09:42:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Hugh Prescott
2005-09-29 09:59:47 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Randy Gordon-Gilmore
2005-09-29 10:10:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Hugh Prescott
2005-09-29 10:12:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 10:15:50 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 10:20:41 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 10:50:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-09-29 13:49:14 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-09-29 13:59:11 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
George Taylor, IV
2005-09-29 14:47:37 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Tom Harrison
2005-09-29 15:40:38 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
caedave
2005-09-30 04:01:38 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Raymond Heckert
2005-09-30 19:49:59 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-02 11:47:41 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-10-02 13:15:26 UTC
Re: Hp 7475 Plotter Servo's
caedave
2005-10-03 05:06:06 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-03 08:00:58 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
turbulatordude
2005-10-03 11:06:16 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-04 07:11:07 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Stephen Wille Padnos
2005-10-04 07:33:42 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Jymmm
2005-10-04 09:36:44 UTC
Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-04 11:14:20 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-04 14:42:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-20 09:33:45 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Russ Waters
2005-10-20 09:51:47 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
wbhinkle@a...
2005-10-20 10:01:24 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Hugh Prescott
2005-10-20 10:22:17 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Alan Marconett
2005-10-20 10:35:37 UTC
RE: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's, 3D surface modeling for EGG-BOT
Victor A. Estes
2005-10-20 10:40:18 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Roy J. Tellason
2005-10-20 10:41:43 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
wbhinkle@a...
2005-10-20 10:44:18 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-20 11:22:37 UTC
Re: [CAD_CAM_EDM_DRO] Hp 7475 Plotter Servo's, 3D surface modeling for EGG-BOT
emc3zach
2005-10-20 14:29:58 UTC
Re: Hp 7475 Plotter Servo's
Roy J. Tellason
2005-10-20 15:58:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's
Victor A. Estes
2005-10-21 06:17:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hp 7475 Plotter Servo's